0
2000-2005 Dodge & Plymouth Neons
The 2000-2005 Dodge and Plymouth Neon was a second-generation car manufactured by the Chrysler Corporation. This car was only available as a four-door sedan. It featured a 2.0-liter engine and a 105.0-inch (2,670 millimeter) wheelbase.
2,349 Questions
How do you adjust the headlights on a dodge neon?
There are 2 screws per side on the outside of the light assembly. They have springs behind them. One is on top or bottom for elevation and one on the side, usually the side towards the middle of the car, for left and right.
2000 dodge neon Speed o and temp gauge dont work?
i have sort of the same problem on my dodge 2000 the temperature gauge recently went out and i replaced the sensor but the gauge always reads 0 your not alone with this one...
Why does heater in a 2000 Dodge Neon only blow cold air?
you may not have the heater water hoses plugged in
How do you set a 2001 neon clock?
Check your user manual. If you don't have one, look for the Hour/Minute button or buttons located near the clock. You should only have to press the buttons to adjust the time. A 2000 Neon has them on the clock and requires a pen to change them.
Why would my odometer say fuse in my Dodge Neon?
The iod fuse is blown. That is in the under hood fuse box, it feeds the domelights, radio, etc..
When do i need to change a timing belt in a 2004 dodge neon?
you usually need to replace a timing belt every 60,000 miles, so if you just purchased the vehicle it is better to have it replaced.
What are some good rims and tires for neon srt 4racing rims?
It depends on your preference and steel or aluminum wheels. Bassett wheels makes good steel wheels and some tracks require steel wheels. Tires are totally a matter of preference as there are literally hundreds of different styles and brands.
Problem starting my dodge neon?
the starter? the battery? Distributor? idk give more information... does it click?
Where is inerta switch on 2003 dodge neon?
Dodge doesn't use inertia switches. The fuel system is computer controlled with relays.
Where is the engine mount for a dodge neon 2000?
the top one is located by the belts next to the valve cover. the bottom one is in the same location but right under the engine in front of the front passenger tire. you can see it poking out if you just look on the underside of the car.
Lower right engine mount 2000 neon?
I think they call it the transmission mount on rockauto.com I replaced the both passenger side ones and am about to do t he drivers side. This site will be of help http://www.ertyu.org/steven_nikkel/neontsbs/2000/09-01-99.pdf
How do you replace license plate bulb on a 2000 dodge neon?
== # Remove screws attaching license plate lamp to rear bumper # Remove lamp from bumper. # Remove bulb socket from lamp. # Pull bulb from socket. == # Install bulb into socket. # Install bulb socket into lamp. # Place lamp in position. # Install screws attaching license plate lamp to rear bumper.
How much does an automobile weigh?
it depends what vehicle a truck can weigh more than a car. and a motorhome weighs more than a ford contour
Wrench size to use on 2000 dodge neon drain plug?
If it's the "oil" drain plug, the size wrench is, better yet use a socket wrench=13mm.
Where is the oxygen sensor located on a 2002 dodge neon?
There is one on each side of the catalytic converter.
Dodge Neon 2000 with a code P0743?
Trouble code P0743 means: Torque Converter Clutch Solenoid Circuit Electrical
P0304 is a cylinder #4 misfire, start with new plugs and plug wires.
Why will your key not turn if it is in park also the steering wheel Will Not Lock at all?
The key cylinder has failed.
How do you replace the oil pump on a dodge neon?
SOHC, '97, 120KMi.........shy of an overhaul the whole engine-front must come off, for a timing belt/tensioner, water pump, oil pump, drop the oil, filter, & oil pan. There are YOUTUBE step-by-step coverage, -OR- you can actually get a manual and dive in. MODERATELY SIMPLE........
just tedious. Oil pump can be removed - AFTER oil pan is removed - a captured P/U tube.
After all of this fun - remove the valve cover - adjust valves (unless hydraulic) and
replace with 4 new Vertical Spark Plug Pipe seals and cover gasket. This will take care of the tubes from flooding with oil.
120K was enough for the Automatic.....
Drop that hazard, replace every Cup-N-Bearing, Clutch & steel, gaskets & seals.........
Nice rebuild ! The valve body MUST be reprogrammed -TO- manual shift.
Unless you want to return home in 1st or 2nd.......the governor counterweights ARE
NOTORIOUS for sticking. Call Superior Products and ask for a KIT for a 404-413-670.
A pleasure to drive, with the mind on other things, than a jar of Rolaids.
Now for that pukey sound system.......
-P- 4258065209
Need help with trouble code p0325 on a 2004 dodge neon?
Trouble code P0325 means: Knock Sensor 1 Circuit (Bank 1) Replace the Knock Sensor
2003 srt-4 low oil pressure light comes on when stopped then goes off when driving?
could be low idle speed or a dirty oil sensor. if it goes off during driving you are fine my ford taurs does that and haves had for the last year or so. i just check and change the oil every 3000 miles and drive on.
How do you program a keyless entry remote for a 2002 dodge neon?
=== === # Insert the key into the ignition switch, and turn the ignition switch to the RUN position without starting the vehicle (allow chimes to stop). # Using your old RKE transmitter, already programmed to the car, press and continuously hold down the UNLOCK button for 4-10 seconds. # Within the 4-10 second time range, continue to hold the UNLOCK button and press the PANIC button. Both buttons may then be released. Upon the PANIC button being depressed, the message for customer programming mode will be transmitted to the RKE module. # A chime will be heard to verify that the customer programming mode has been entered (allow 3 seconds to hear chimes). # Press and release any button on each transmitter that is to be programmed to the RKE module, including any transmitters which were previously programmed to the RKE module (with a maximum of four possible). After each transmitter is successfully programmed, a chime will be heard to verify that successful programming of the transmitter has occurred. # You may reprogram your old transmitter back into the car if it still works correctly. If not you may program up to 4 new RKEs. # After thirty seconds, or upon the ignition switch being turned OFF, the RKE module will exit programming mode.
