Chrysler Pacifica

That actually says GASCAP. It means that the PCM has detected a large vapor leak from the fuel system and it assumes you have left the gas cap loose.

That actually says GASCAP. It means that the PCM has detected a large vapor leak from the fuel system and it assumes you have left the gas cap loose.

There are three screws that need to be taken off when changing the filter; the two that hold the top down(located on the left and right side of the casing as you are looking down at it from the passenger side of vehicle) and the one that is mounted on to the frame. Once these are taken off, you can maneuver the top of the case off and replace the filter.

if your 04 is like my 06...stand to the passenger side of the hood near the middle theres a medium black case..should be your air filter...you will need a screwdriver or tool to remove the two screws in front of the case..the front is the side away from you''once you remove the to screws you have to push on the side nearest you to release or unsap the case..raise it up and remove filter

It is on the bottom rear of the engine oil pan.

5x127mm

If your tpms indicator is on in your Chrysler Pacifica and you have already fixed the tire pressure issue, simply continue driving a few miles and the sensor will reset itself. It usually only takes about 4 miles to reset it.

22 gallons

set the presssure to 40 psi per tire to override the low pressure and then put it at normal. it worked form me

it is under the back of the vehicle. When you open the tailgate, there is a small floor compartment you have to open and use the lug nut wrench to lower the plate that the tire is on

Lift the engine compartment hood. Remove the headlight retaining bolts. Remove the wiring harness. The headlight will come free. Reverse the process to install the new headlight.

I have had the same problem. I simply removed the broken plastic handle which left the cable with a metal hook end exposed which you can pull directly toward the rear of the car. It is a little uncomfortable and works better with gloves. I am looking for a replacement online, but haven't found one yet

Locate the filter compartment, and on front and back of the compartment is two screws. Pull them out. Then give it a nice little bump with the heal of your palm to get it to loosin up and the top half will pop right off exposing the filter.

You will need to have the code read with a scan tool, repair the cause of the codes, and then the code can be erased with the scan tool.

Yes

I assume you are referring to the Heated oxygen sensor (HO2s). You access it from under the car. It is located within a few inches of the rear exhaust manifold. Its electrical plug is secured right next to the rear HO2s electrical plug. The front HO2s electrical sensor plug is black. The rear one is white. A side note: Only use the OEM Denso brand sensors on these cars, Also, check the heater circuit in the sensor before installation (the 2 black wires). It must be between 2.1-2.7 ohms. Many aftermarket sensors won't meet this spec and will throw a DTC for HO2s heater failure. Trust me on this one. I just recently repaired a Pacifica. A new Bosch and a new Delphi sensor both failed the heater test, miserably. Anyway, if your car is front wheel drive only, access is super easy. AWD is a little more difficult. Good Luck! MGL

Red, 5 year, HOAT type.

it is in the center of the drivers foot well right under the dash

The amp is located on the passenger side rear beneath the cargo area floor.

It's likely the thermostat. That's assuming the coolant is full. Thermostat runs $11 for the 3.5.

It will vary depending on if you have HID lighting or Halogen Lighting which you did not include in your question. 2005 Chrysler Pacifica headlight bulb general replacement procedure: Purchase the correct replacement headlight bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the headlight bulb lamp replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).

In the storage compartment in the floor behind the rear seats. You have to fold down the seats to get to it. And go to the Chrysler website for an owner's manual.

to chang ethe brake bulb, first lift up the rear hatch of the car, look to see what brake light is out, the you nee to look on the inside of the tail light assembly and you will see 2 scews or bolts holding the assembly in place take out those bolts and pull out on the brake light. next you will then turn the middle connector half a turn till it unseats itself from the assembly then you can replace the bulb

You open the rear hatch, and remove the two plastic hole covers from the top center trim piece. They allow you to access two phillips screws that go straight up. Once both screws are out, that center trim piece snaps down (it is held by three plastic snap clips). With that piece out of the way, you can reach up above the headliner and get to a 10mm bolt that secures the antenna base. Two wires attach to the antenna, and the connectors are easy to disconnect once you find the tab to release them.

Red, five year, hoat type.

There is a button on the dashboard,, just right of the instrument panel, it says us/met.

Depress that button and everything turns to opposite of what it was.