Electronics Engineering

yes,obviously its good to have high bandwidth....according to technical feild

²Communication difficulties

§Different disciplines use the same terminology to mean different things. This can lead to misunderstandings about what will be implemented.

²Differing assumptions

§Each discipline makes assumptions about what can and can't be done by other disciplines.

²Professional boundaries

§Each discipline tries to protect their professional boundaries and expertise and this affects their judgments on the system.

A register.

All a.c. voltages are expressed in root-mean-square (r.m.s.) values, unless otherwise stipulated. So 12 V is an r.m.s value which, for a sinusoidal waveform, has an amplitude, or peak value, of 1.414 x 12 = 16.97 V. So its peak-to-peak value will be twice this amount -i.e. 33.94 V.

A: Actually no. If the current can be limited it may Even oscillate and each diode will behave differently even tough they are from the same family. A reverse breakdown usually means a blown diode in a circuit the hear from a hi voltage and the hi current will surpass its power dissipation and blow short most of the time.

According to the EIA-96 system which applies to SMD resistors, it means 10K (10,000 ohm), 5% tolerance.

QN+1=T exor QN

M (usually as a capital) million. As "m" strictly is a thousandth (as in mm=millimetre), but I've never seen it for that purpose.

radio frequency for link to bts to bscs/msc

Only frequencies in the pass band range will be allowed through the circuit. Other frequencies will be attenuated based on the RC values picked.

dc motors can be operated at no load as well as at load condition.But by using the swin burns test the efficiency can be calculated at no load which is more benficial than load test.At industries this swin burns test is used because for load test we have to give separate supply for the load to run.In no load test that power is saved.

The governor controls the speed of the power source rotating the generator.

This has to be continually adjusted to match the load on the generator.

As more load is switched on, the generator becomes harder to turn, this would cause the generator to slow down, unless the power unit is adjusted to increase power and correct the speed.

A: A BCD code must be decoded to provide a seven digit output to the 7 bars display that is the only way to see the binary number visually.

A: It is a relay or another noise maker the sing out if a moist detector sense either no water or water to give an alarm by sounding off

Hooter is an alternate name for buzzer or alarm device.

A: Drift voltage is an an wanted voltage that wander off from what is expected. I sources for wandering could be thermal or a component drifting in value.

the goal of write assembly cache is to assemble writes so that they can be transmitted to memory in an orderly way.

A: If its polarized it will have a bar running along side of the body, A grade capacitor will either have stamped a -+ on it terminal and occasionally a red and black paint dot red is positive. If there is none of these marking then it is not polarized and does not matter how it is connected

Joules is equivalent to power over time. Power is equivalent to volts times current, so your question does not provide enough information to answer.

To look at another way - you might ask how many joules (a measure of energy like kWh - what your electric company bills you on) are in 120 volts. If this were not dependent on current, then you would be constantly billed for every outlet in your home, regardless of whether they are in use. The fact that 120 volts is present at all outlets at all times does not mean that power is being used at all times.

applications of common source amplifier

Stabity factor is not a circuit.It is a parameter,which decides the ability of Biasing circuits,to keep the Q-pt stable in the center of DCLoadLINE.It should be as low as possible

It is an inverting comparator with a positive feedback, can convert an irregular shaped waveform to square waveform. it is also known as squaring circuit.

sudhanshu kumar

siliguri institute of tech.

ece(2nd year)

A: The gain of a transistor is not linear and even that varies from component to component. The gain can vary greatly depending on the Ic current and the load. Manufactures only give out a typical gain for a particular current. As a rule the lower the Ic current the higher the gain. To really find out what a particular transistor characteristics are a tektronik curve tracer is used.

A: THYRISTOR can be used to clamp damaging energy as opposed to a fuse that must blow open and invariably takes time to blow. A thyristor is much faster and controllable actually if the problem disappear it can be made to open up again and restore power for normal operation.

1. Transition capacitance

2. Diffusion capacitance

3. Space charge capacitance

4. Drift capacitance