Fireplaces

Burning produces smoke (carbon) and gasses, such as Carbon Dioxide and Carbon Monoxide, along with water vapor. Ash is left after the wood is burned. We use our wood ash as fertilizer in our garden, for our grapevines, etc.

When a log burns in a fireplace, the matter in the log undergoes a chemical reaction called combustion. The heat from the fire breaks down the chemical bonds in the wood, releasing energy in the form of heat and light. The carbon in the wood combines with oxygen in the air to form carbon dioxide and other byproducts like water vapor and ash.

Something is preventing your fireplace from drawing. The damper may be closed, or partially closed. Your chimney may have a blockage, or you may have prevailing winds that push smoke back down the chimney. If you have air flow problems, such as a vent fan that draws air out of the house, it can cause that. Bottom line- if the damper is open, and the flue is not blocked, you need a good fireplace/chimney specialist to examine what you have.

A gas clothes dryer emits carbon dioxide (CO2) as a byproduct of the combustion process that generates heat for drying clothes. It is important to ensure proper ventilation when using a gas dryer to prevent indoor air pollution.

Gas fireplaces typically receive gas from a direct gas line connection in the home. The gas line provides a continuous flow of gas to the fireplace, allowing it to ignite and create flames. The gas flow can be controlled and regulated using a valve or switch on the fireplace.

The energy conversion that occurs is from thermal energy (heat) produced by the fireplace to thermal energy absorbed by your feet, increasing their temperature.

Wood catches on fire when it reaches its ignition temperature, typically around 300°C (570°F), causing the wood to release flammable gases. These gases mix with oxygen in the air, creating a combustible mixture that ignites. Once ignited, the wood continues to burn as long as there is a continuous supply of oxygen, heat, and fuel.

A gas smell when a gas fireplace is turned off may indicate a gas leak, incomplete combustion, or a problem with the gas line or burner. It is important to have a professional inspect and repair the fireplace to ensure safety and proper functioning.

Yes, wood density does affect the burning time. Denser woods typically burn slower and longer than less dense woods because they have a higher energy content and slower combustion rate. Softer woods with lower density tend to burn faster and produce less heat.

Seasoned (dried) oak weights about 4000 lbs. or two (2) tons.

A cord is defined as 128 cubic feet (3.62 m3), corresponding to a woodpile four (4) feet (122 cm) wide, four (4) feet (1.2 m) high and eight (8) feet (244 cm) long. So the weight would depend on the type of wood.

a cord of wood is the amount of wood in a stack of 48-inch logs (or cut logs equaling 48 inches) that is 4 feet high and 8 feet wide

The Orsat apparatus is used to analyze the composition of flue gases, typically measuring oxygen, carbon dioxide, and carbon monoxide levels. The apparatus involves passing a known volume of flue gas through different chemical solutions to absorb specific gases, allowing for quantification of each component. This analysis helps assess combustion efficiency and environmental impact of fuel-burning processes.

Hardwoods such as oak, maple, ash, and hickory are typically good at burning because they are dense and provide a longer burn time and more heat output. Softwoods like pine and spruce can also be good for starting fires due to their quick ignition, but tend to burn faster and produce more creosote buildup.

In the USA, at 110 volts, 1500 watts just about uses all the capacity of a 15 amp breaker, there's only 150 watts spare, look at the rating of the lamp and fan - lamp may be 40, 60, 100 watts, fan 40, 60, more? In the UK and Europe, at 230 volts, there's no problem. I give both answers because I don't know where you are.

When wood is burned, the carbon in the wood combines with oxygen in the air to form carbon dioxide, leaving behind black carbon residue known as charcoal. This is why the wood turns black when burned.

If you are not hearing or smelling gas when the gas fireplace is turned on, but the pilot light is working, the issue may be with the gas valve not fully opening or a blockage in the gas line. It is important to have a professional technician inspect and service the fireplace to ensure safe operation.

it depends on the fire place. traditional fireplaces loose most of their heat via the chimney. ventless fireplaces loose 99.9 percent of their heat out of the front of the fireplace and into the home

It is not advisable to use a 20 lb propane tank on a fireplace designed for natural gas, as the pressure and fittings may not be compatible. It is best to use the type of fuel specified by the manufacturer to avoid potential safety hazards.

An aerosol can should not be thrown into a fireplace because it can explode when exposed to high temperatures, leading to serious injury or property damage. The pressurized contents of the can, such as gas or flammable liquid, can cause the can to rupture violently. It is safer to dispose of aerosol cans properly according to local guidelines.

A ringing noise from a gas fireplace can be caused by a buildup of debris or dirt on the burners, improper gas pressure, or a faulty pilot light. It's best to have a professional inspect and service your fireplace to diagnose and correct the issue to ensure safe and proper operation.

Fire is not a physical or chemical property. Fire is not a property. Fire is a chemical reaction where oxygen combines with some or all of the chemical components of the fuel, emitting light and heat.

Bio bricks are considered a more environmentally friendly option compared to traditional wood because they are made from compressed sawdust and other wood byproducts, reducing waste. They also burn more efficiently and produce less smoke and ash compared to regular firewood. However, the choice between bio bricks and wood ultimately depends on individual preferences and needs.

To replace a thermocouple on a gas fireplace, first turn off the gas supply and wait for the fireplace to cool down. Locate the thermocouple near the pilot light and unscrew the old one from the gas line, then install the new thermocouple by screwing it in place and reassemble the gas line. Finally, relight the pilot light and test the fireplace to ensure the new thermocouple is working properly.

LP gas stands for liquefied petroleum gas, which is commonly used for heating, cooking, and powering vehicles. It is a mixture of propane and butane gases that are compressed into a liquid form for easy storage and transportation.