Ford Fusion

According to the 2013 Ford Fusion Owner Guide :

The tank capacities are :

( front wheel drive , 16.5 U.S. gallons )

( all wheel drive , 17.5 U.S. gallons )

Disconnect all pipes, wires, ancillary equipment and fixtures and fittings. Disconnect from transmission components. Disconnect from chassis. Lift out engine.

Replace with new engine ensuring all connections are made to the correct specifications.

Regular UNLEADED gasoline, up to 10% ethanol. Does not require high test, not made for E85 fuel.

According to the 2010 Ford Fusion Owner Guide :

Front wheel drive ( 17.5 gallons U.S. )

All wheel drive ( 16.5 gallons U.S. )

you pull it out.

Did it on a 2008 with four-cylinder engine (FNR5 transmission). Take off the belly pan, drain the transmission fluid, support the engine, remove the single large bolt for the motor mount on the passenger side, raise the engine slightly, unbolt the transmission pan. Shift solenoids are inside.

In the front passenger footwell area , in the right upper corner ( according to the

Owner Guide )

50,000 Miles

If you wait too long it just risks your chance of them cracking or causing more problems. Spark plugs are cheap and easy to do.

I own one of this beautilful cars and you can ride up to five passengers

You drain the old gear oil by removing the drain screw. Replace the rubber washer seal with a new one and reattach the drain screw. Remove filler cap and fill in 3 qts of 75w-90 gear oil all the way to the top of the reservoir Replace filler cap. Check for leaks. Drive around and check again for leaks.

The error code E24 on a Ford Fusion CD player means there is an internal electronic error. You should try cleaning out the CD player.

by removing the fuel tank.

It depends what your bolt pattern is, accords from 2003 and up have the 5 lug 4.5 inch or 114.3mm bolt pattern, civic's from 2006 and newer have the same pattern, as do 2006 and newer Ford fusions. I have a 2009 civic Si and a 2006 fusion SEL and are interchangeable. BUT the smallest rim size to fit a fusion SEL is 16 inch. If your honda is one of those years and has 16" rims they will fit your fusion.

The curb weight of the 2013 Ford Fusion is 3615 lbs..

Ford started designing the Fusion in late 2003. The car debuted in the middle of 2005, as a 2006 model. The Fusion had a makeover for 2010 and is one of the best-selling vehicles in the USA.

Not sure what engine you have.

I know on the 2.3L 5-speed automatics, it's between the battery and alternator cooling duct. Look for the red cap

to change the spark plugs there are 5 steps to this:

step 1: remove spark plug wires.

step 2: find the right size spark plug socket and rachet.

step 3: losen spark plugs until they come out.

step 4: install new spark plugs into cylinder, but make sure not to cross thread them it is very easy.

step 5: replace spark plug wires on to new spark plugs.

and youre done

The 2014 Ford Fusion has a 6-speed shiftable automatic.

On my 2006 fusion there is no tube. The evaporator box has a short nipple that directly exits outh through the firewall towards the front of the vehicle. Impossible to get to from outside... Peel the carpet back on the passenger side and you will see the bottom of the evaporator box.

1 - 4 - 2 - 5 - 3 - 6

It has the Coil On Plug ( C.O.P. ) ignition system

The engine cylinder locations are numbered :

firewall

1-----2-----3

4-----5-----6

front of V6 Ford Fusion > driver

Round switch to left of steering wheel on the dash. Turn clockwise. Pull towards you for fog lamps (if you have them).

The block heater cord on a 2012 Ford Fusion is located directly behind the upper edge of the grill. You have to lift the hood to plug in. This is a peeve of mine as I don't particularly like having to lift the hood to plug in at -40 when the hood is frozen shut!

no fuel replacement needed

What engine light. If you are referring to the Check Engine light then reset it with an OBD2 scan tool after the problem is repaired.

Follow the next steps: 1.- Remove the plastic cover surrounding the radio.. You can do it either with your bear hands or using the right tools (wich I recommend) do it carefully, if you bend it too hard it will brake. There is no screws you need to remove on that plastic cover. 2.- There are 4 screws (milimetric head) which hold the Radio/CD player attached to the frame. 3.- Unplug the harness, power cord and antenna. Voila! you are done!