Home Appliances

If your clothing is coming out still-dripping wet, the spin cycle is not engaging. Try using a different setting on the washer. When you hear the spin cycle begin to engage, peek into the washer and see if the drum is actually spinning. DO NOT put your hand in the machine and try and start the drum spinning. If the drum does not spin up on its own, then you need repair on the washer. You might also be over-loading the drum. Have it looked at, but it is often an easy fix.

No, a 1000-watt electric heater operating at 110V will produce the same amount of heat as a 1000-watt heater operating at 220V. The power output (in watts) determines the amount of heat produced, not the voltage.

An out of balance load. To much weight on one side od the drum. Avoid washing heavy items like jeans, with light weight items like t-shirts. The jeans weigh more when wet and will put the load out of balance. If your load starts to shake, open lid, wait until the drum stops spinning, then even out the load in the drum.

To correctly wire a three-blade 220-volt plug, you should connect the hot wires (usually black and red) to the brass-colored screws, the neutral wire (usually white) to the silver-colored screw, and the ground wire (usually green or bare copper) to the green screw. Always make sure to follow the specific instructions provided by the plug's manufacturer and to disconnect power before working on any electrical connections.

To vent a gas dryer safely, use a rigid metal duct to vent to the outdoors, rather than a flexible duct that can collect lint and pose a fire risk. Make sure the venting system is secure and free of any obstructions to allow proper airflow and reduce the risk of carbon monoxide buildup. It's also recommended to have a professional inspect and clean the venting system regularly to ensure safe operation.

This isn't an answer- it's from the questioner :) Just to clarify: This is the small, apartment-sized, stacked washer-dryer unit. They used to commonly come in 110V. They are still out there but old and sell for same price used as the used newer 220V. So we'd like to buy a newer used 220V and convert if possible and safe. Don't know the watts on these, tho. But must not be as large as regular sized dryers?

The lowest access point on a low-pressure centrifugal air-conditioning appliance is typically at the inlet to the centrifugal impeller. This is where air enters the unit for the cooling process. It is important to ensure proper maintenance and access to this point for inspection and cleaning to maintain the efficiency of the appliance.

Arm and Hammer laundry detergent is made through a manufacturing process that involves combining various ingredients such as surfactants, enzymes, and fragrance. These ingredients are mixed in specific proportions to create a cleaning formula that effectively removes stains and odors from clothes. The final product is then packaged and distributed for sale to consumers.

1. Dryer sheets often contain chemicals such as phthalates, which can have negative effects on respiratory health and skin irritation.
2. When disposed of, dryer sheets contribute to environmental pollution through the release of harmful chemicals into waterways and soil.

Nathaniel B. Wales and Alfred Mellowes invented the refrigerator in 1916. Frigidaire, which was founded as the Guardian Frigerator Company in Fort Wayne, Indiana, was the company that developed the first self-contained refrigerator based on their invention.

Putting a lighter in a dryer is dangerous as the heat from the dryer can cause the lighter to explode, leading to a fire. It is not safe to place any flammable items like lighters in a dryer.

Silver-colored material helps when ironing because it reflects heat back onto the fabric, allowing for more efficient ironing. This helps to smooth out wrinkles and creases more quickly and effectively.

You may need a gas dryer if your home already has a natural gas line available and you want a more cost-effective option for drying your clothes. Gas dryers tend to be more energy-efficient and can help reduce utility bills compared to electric dryers. Additionally, gas dryers usually have faster drying times and are preferable for larger loads of laundry.

The process used in washing machines to squeeze water from clothes is called the spin cycle. During this cycle, the drum rotates at a high speed to force water out of the clothes, allowing them to dry faster.

No, it is generally not safe to use a 220 volt adaptor with a 110 volt appliance. Doing so can cause damage to the appliance and may pose a safety hazard. It is recommended to use the correct voltage adaptor or converter for the specific appliance to ensure proper functioning.

That's backwards, as a washer is much heavier than a dryer, particularly when it's full of water. There are over/under units, but you can't simply set a regular dryer on top of a regular washer (or vice versa, which is a bad idea anyway).

No, it is not recommended to use a 9-volt charger for a 4.5-volt appliance. Using a charger with a higher voltage than what the appliance is designed for can damage the appliance or pose a safety risk. It is best to use the charger that is specifically designed for the appliance.

480 volt control circuits work by using 480 volts of electrical power to control the operation of various electrical devices such as motors, lights, and heaters. The control circuit typically includes a control panel, relay switches, contactors, and push buttons to regulate the flow of electricity and activate or deactivate the connected equipment. These circuits are designed to provide a safe and efficient method of controlling high-power electrical components in industrial applications.

Go to home depot, purchase the 4 wire power cord. The directions aren't very clear. But most of the colors are pretty self explanatory. White in the middle, red to red, etc. The green one is the confusing part. There is a green wire coming out of the back of the unit. It needs to be grounded on something metal, like the body of the dryer. AND the green wire on the new 4 wire power cord you are attaching needs to be grounded too, also to the body of the dryer unit. There is usually an extra screw/bolt on the body of the dryer to attach it to so it continues to ground out. You can google around, but doing it yourself will save you from hiring an electrician. The new 4 wire power cord was 14.99 for a 4ft one and 17.99 for a 6ft one. Just remember to attach the cord to the dryer before plugging in!!! Also, some how we flooded our outlet so we had to trip the fuse switch in the garage. So if at first it doesn't work, start over at the beginning and make sure the fuse is on in the fuse box. Also, we thought there was something wrong b/c the fuse looked like it was on, but it was kind of in the middle, so make sure you switch all the way off to all the way on so you can be sure it's on. Good luck, remember safety first!! ~rach

This is a common topic here. Firstly, if you are installing new work go with a 4 prong oven outlet. 3 prong outlets are old and do not meet code for new work. To install, you need to run 6/3 romex wire from your main panel to your new outlet. Install the new outlet in a box behind your oven. Wire up the 6/3 in the panel to a 50A 240V breaker. Remember the color code: Black/red/brass screw is hot, White/silver screw is neutral, bare wire/green screw is ground. I also recommend buying a book on home electricity repairs. It will show you how to do it right and serve as a handy reference during the job. As always, do it right or hire someone to do it for you. Negligence is fatal with electricity.

One disadvantage of appliances that work on the heating effect is that they can be energy intensive, leading to high electricity consumption and potentially higher utility bills. Additionally, these appliances can pose a fire hazard if not used properly or if they malfunction, making safety a concern.

The switch contains a sandwich strip of 2 metals with two different coefficients of thermal expansion. The dial you would turn to control the temperature modifies the resistance of the circuit - thus current (or would be set digitally nowadays). When the desired temperature has been reached, one of the metals stretches more than the other. The metal sandwich curls, thus disconnecting the contact of the switch.

A chlorine concentration of 500 ppm is much higher than the safe limit for dishwashing, which is typically around 50-100 ppm. Continuing to wash dishes with this high chlorine concentration can pose health risks due to potential chemical burns, skin irritation, or respiratory issues for the dishwasher. It is important to immediately stop using the sink, thoroughly rinse and drain the sink, and then re-measure the chlorine concentration before resuming dishwashing.

A noisy water heater can be due to mineral buildup in the tank, causing sediment to collect and harden at the bottom. It can also be caused by a loose heating element or expansion and contraction of the tank due to temperature changes. Regular maintenance and flushing of the water heater can help reduce these noises.