0
John Deere
John Deere is the leading manufacturer of agricultural machinery in the world. Questions about John Deere products and their proper operation can be asked here.
2,566 Questions
What is the gas to oil mix in a John Deere cs62 chainsaw?
mix it as can of oil says.they say 25 to 1 others 50 to 1 there oil whatever i mix my oils for all my saws around 35 to 1.i have not burn one up and i run 7 saws.one of them i still use is 30 years old with original piston and rings.
What is the selling price of a 1977 John Deere 4430 tractor?
Earlier this year I purchased a 1984 316 with Onan engine for $1100.00 dollars from our local Deere dealer. They were asking $1400.00 dollars. Mine was probably above average condition, with no visible damage to fiberglass. It runs fine, but uses conciderable oil. It also came with a 46" deck in good condition. If you have more questions concerning John Deere garden tractors, use should check out, www.weekendfreedommachines.com , a great forum site with tons of information.
EDIT: The 1978 model 316 was a 1-year-only model and is totally different from the later 316 which was produced beginning in 1984.
How much hydraulic fluid does a 4020 John Deere hold?
WITH NEW TRANI FILTER AND COMPLETE DRIAN FROM PLUG YOU WILL NEED 5QUARTS OF THE low vis oil from john deere dealer
What is the chevron equivalent to John Deere HY-Gard J20C?
Shell's Donax TDL meets the J20D requirement. The Donax TD meets the John Deere JD20C requirement.
How do you change fan belt on john deere 4020?
hi, i recently purchased an old JD 524. To remove the old belts you have to "split the snowblower between the impellers (round part) and the housing that covers the drive gears. (square part).There are 4 bolts you need to remove, 2 upper and 2 lower , Also you will need to take the bottom cover off to get on the nuts for these bolts, after you remove them and a pesky spring that is in there, the blower will split into 2 parts. Once split you should be able to get the belts out. I havent put new ones in yet so youre on your own for that one, but should be able to go in the way they came out. good luck
How do you find the age of a John Deere lawn mower?
The age can be determined. Take the serial number into your local dealer and they can look it up for you.
What is the weight of a m john deere?
A John Deere M weighs 2,600 lbs [1179 kg] while a John Deere MC weighs from 4000 to 4150 pounds.
Where is Location of spark plug in a john deere 345 lawn tractor?
Setting in the seat of the lawn tractor, it is on the front and right side of the motor close to the hinge area for the hood of the lawn tractor. You will see a black wire about the diameter of a pencil that slips over the plug.
_____
|_____|\ o\ < - it will be angled (where the o is) from the front and the side of the motor.
John Deere 1988 F510 pto will not start?
If it only shuts off when the PTO is engaged it could be the field coil on the PTO is drawing too much current and activating the self resetting Circuit Breaker attached to the starter solenoid. This happened to me on our 316. If the PTO is shutting off it could be a bad connection on the field coil wire.
I need a mower belt diagram for a John Deere 110?
The John Deere LA130 is a model of riding lawnmower produced by the John Deere Company. The mower uses a 48 inch mower belt. Replacement mower belts are available online and at specific retailers.
Where is the serial number located on a john deer tractor l130?
On lawn mowers it is on the side of the frame. On most other tractors it is on the back main case of the tractor above the PTO on the back side.
How do you replace the deck belt on a john deere lt166 freedom 42 deck?
It depends on the Mower Deck you have. I have an LT166 with a Freedom 42" mulcher mower deck. To change the belt, I:
1) Lower the Mower Deck to the bottom position (on the lowest grass height)
2)Remove the front cotter pin and connector that locks the mower deck to the front of the tractor. The connector looks like a square loop with a tail. Slip the mower belt off the tractor (it should be loose and easy to do).
3)Remove the cotter pins that attach the lifter arms (on both sides) to the deck.
4)Remove the cotter pin that attach the blade brake to the tractor. Remove the blade brake shaft from the tractor (it should just slip off)
5) Raise the mower deck lever on the tractor -- the lifter arms should slide out from the mower deck.
6)Slide the mower deck out from under the tractor.
7) Remove the screws that hold the black plastic cover of the deck.
8) Find the spring tensioner on the side of the deck under the cover. Loosen the nut that keeps the spring tensioner tight, until the spring moves freely.
9) Loosen the nut on the FORWARD gear (the one the tensioner is connected to). That gear will then move so you can remove the belt.
10) Replace belt (Make sure the blades on the Freedom deck are aligned first!). Tighten spring tensioner. Tighten nut on forward belt gear.
11) Reverse steps 7,6,5,4,3,2,1
Where can i find John deere Sabre 1338gs deck belt diagram?
Check with your John Deere dealer. No, not Home Depot or Lowe's but an actual business that works on and sells John Deere mowers.
What is the firing order on a john deere 1010 special tractor?
I have a 1962 Row Crop Utility John Deere 1010.
Everywhere I read said the firing order was 1-3-4-2, BUT, after much messing with my new distributor, I have found that mine is most definitely 1-2-4-3.
Mines a pre- 36000 serial # (or is it 3600?).
Also - not that it matters for 1-2-4-3, but the front cylinder (furthest from driver) is #1.
Where do you fill the hydraulic fluid on john deere 4440?
To check hydraulic fluid in a 2040 john deere when setting in the seat with both feet placed on foot boards look on right side behind your heel of foot. Look all the way back to area where axle housing, foot floor board (right foot) and rear housing under seat meet. There will be a small cap that will unscrew and when pulled up will have a dipstick on it.. This cap will look like an old dimmer switch like used to be in trucks or cars. It really doesn't stand out and is about level with the floorboard...
Where might one purchase a John Deere blade for a lawnmower?
The best place to purchase a John Deer snowblower is to visit a local hardware store which specializes in outside products and services. A great place would be Canadian Tire, Sears, Walmart, etc.
AM 101207 crosses to a Fram PH 7575. To see what other manufacturers numbers are, use the Fram web site, it will give a listing. That number also is the John Deere replacement for a Kohler 52 050 02 oil filter, (used in the Deere STX46) probably others too. Link http://www.power-21.com/honeywellpower21i/Application.aspx?b=F&vt=4
Where is the hydraulic filter located on a 430 diesel John Deere lawn tractor?
There is a filter housing on the right side of the transmission just in front of the rear axle. Unscrew bold in center of housing to remove, BUT FIRST remove housing drain plug or you will have oil running your arm. Filters are usually available at TSC. Be careful when reinstalling to get the gasket seated before tightening housing.
How much hydraulic oil does it take to fill 1130 john deere tractor system?
Crankcase: 5 qts (4.7L)
Hydraulic: 32 qts (30.3L)
How many quarts of oil are needed for john deere la 105 mower?
Diesel will hold 12 quarts and Gas will hold 8 quarts
How can I check the timing on a John Deere 2020 gas tractor?
Connect a timing light according to the manufacturers instructions to the Number 1 (front) spark plug cable. Run the engine at 2500 rpm. Loosen the distributor clamps and rotate the distributor until the "S" mark on the crankshaft front pulley lines up with mark on engine casting as timing light flashes on. When distributor timing is correct, tighten the distributor clamps.
