Kia Sedona

Where is the banck 1 kia sedona 2004

In the 2002, there is an idler beneath the alternator. When it's loosened, the belt relaxes and can be removed. I don't know if it's different in an '04. I had the radiator, air conditioner condensor, and oil cooler out to replace the alternator. I don't know if you can reach the idler without removing these things. I also do not know how easy/difficult it is to rethread the belt since it doesn't just run the alternator.

Wiring diagram for a 2004 Kia carnival.

The fuse box is located on the driver side lower left hand panel. Right next to the parking brake. It just pops out if you pull it.

the plug is located right above the left side (driverside)subframe cross member, (hard to see)going front to rear. Don't know how you would get a wrench in as there is very little clearance.If you could the fluid would drain out on the frame.

Any tips on changing the power steering pump on my kia sedona

It's can be Chrysler, but not Mercedes, because MB 2.9L engine has 5 cylinders, Kia's engine has 4.

The curb weight of the 2004 Kia Sedona is 4802 lbs..

There are either bars or straps behind the seats that you you pull and it detaches the seat from the floor. I Really can't tell you anymore because my husband is the one who does it but it seems to be very simple. Just be careful cause the rear seat is very heavy.

answer

Pull the strap to release the back of the seat and fold it up - at the front of the seat you will see a bar preventing you from tipping the seat up fully. (you don't have to tip tyhe seat up, it just shows you where the bar is).

There are actually 2 of these bars - squeeze them together to release the clip that holds the front of the seat to the floor. The seat should now be free.

The water temperature sensor on a 2002 Kia Sedona is located on top of the engine, near the upper radiator hose. It relays the temperature to the vehicle's computer and triggers the cooling fan to come on.

The height of the 2007 Kia Sedona is 5 ft. 9.3 in. (69.3 in.).

The 2012 Kia Sedona has a 6-speed shiftable automatic.

The gas tank on the 2008 Kia Sedona holds 21.1 gal..

Unfortunately, the only way to retrieve trouble codes after 1995 is with the OBDII scanner. The good news is that there are some auto parts stores that will scan it for you free of charge. Or, you can buy a simple OBDII scanner for about $60.

The maximum cargo capacity of the 2012 Kia Sedona is 141.5 cu.ft..

To fill the oil canister in a 2004 Kia Sedona, the mechanic will need around 6 quarts of oil. The oil should be 5W30 or 10W30 and an oil change for a Kia Sedona should take place ever 7,500 miles, as per the manufacturer's request.

the 4 way flasher switch is located in the center of the dash between the vents with a red triangle on it. it is about 1 inch wide and 2 inches tall

In the spare tire rack under the van, just forward of the rear bumper.

The 2004 Kia Sedona OBD 2 port is under dash below steering column

The gas tank on the 2005 Kia Sedona holds 19.8 gal..

no it does not you are able to get to it uder the black cover of timing belt

It's in the fuel tank!!

First remove engine cover then air filter then remove breather next hoist ready remove rocker mount. Next remove timing belt cover. Next remove timing belt making careful note of where the gear is before removing belt. Make a line out from most vertical or horizontal tooth. If u screw that up ull cause fatal damge to engine. Next remove pump clean off old gasket and sealent. Apply new gasket sealent pump. Then work ur way back putting things back.

Remove the shroud over the radiator by removing the 13 plastic screws. Do NOT use a power screwdriver, these strip as easy as warm butter. These screws are similar to the holders that GM uses where the center post inserts and expands 4 legs out to hold the piece in place. In this case, screws inserts to expand the 4 legs out of the insert. If a screw won't back out, use a knife or thin screwdriver to go under the lip of the insert and apply gentle pressure while screwing out the screw. This will give the screw enough friction to come out. Be sure to use the right size screwdriver to prevent messing up the screw. When the screws are out, remove the plastic inserts that the screws fit into, and then lift the rear end of the shroud up and pull back towards the engine to slide the tabs on the front of the shroud out. Watch for any inserts that you missed that may go flying. Now you'll see 2 10mm bolts, one at the top near the fender and the other near the radiator. Remove these. Push the light housing out by reaching through the hole at the rear (you can see the headlight socket through the hole). There is a plastic guide that may break if you don't take the housing straight out. Disconnect the harness to the light socket by squeezing the two tabs and then pulling it back. Turn the socket 1/4 turn clockwise as viewed from the front of the vehicle. Push the bulb down slightly and turn it to remove. Pay attention to the posts on the socket, one side is higher than the other and you need to know the proper orientation for inserting the right bulb. Replace the bulb, push the socket back in place (ensure it is fully inserted before turning) and reverse the steps to reassemble. Be sure to reinsert the light housing straight in to avoid breaking the plastic guide I mentioned above. I found that if I used the brackets for the 10mm bolts as a reference, it went right in. Took me about 15 minutes. Good luck!