answersLogoWhite

0

Kubota

Kubota is a Japanese company that was founded in 1890. They are a major manufacturer of small to medium sized tractors and equipment. This category is the place for all questions about all things Kubota.

742 Questions

What is the oil filter number for Kubota V2203 engine?

Oil filter part number is 121965

Or you could use the longer and more common Fram PH8A (common on Fords) or equivelant.

Do Kioti tractors use Kubota engines?

No Kubotas use Kubota engines and Kiotis use kioti built engines how ever certain Kioti engine are basically a carbon copy of Kubota designed engines. Daedong and Kubota where building tractors with Daedong metal work and Kubota engines. Kubota suspected Deadong of copying Kubota ideas. The partnership ended but Im pretty sure this is where the link is.

There are some small differences. We run both kubota based engines and the kioti copies in boats in our company. The 43 bhp variant of the Kubota looks very similar to the Kioti. The kioti engines seem to be much more noisy from new and produce much more smoke on start up. In my opinion Kioti is a budget copy.

Where can you find a cross reference for auto oil filters?

All over the place...

- Try wixfilters dot com.

- Try fram dot com.

- Try pureoil dot com.

Your local auto parts store can help you as well.

*** Keep in mind, some companies offer filters that others may not!

Wix is one of the most comprehensive out there.

There are so many more out there... Ya just gotta look!

Kudos! ~AJ

How do you check hydraulic fluid on Kubota L3650?

There is a small round window on the transmission that can be seen just behind the clutch pedal on the left side of the tractor. The hydraulic fluid must be filled so the oil level is between the two lines etched on the window.

It takes about 8 gallons of hydraulic fluid for a drain and fill. The fill hole is under the rubber plug on the raised portion of the seat area between the driver's knees. There are four drain plugs.

Cross reference Kubota oil filter 66021-36060 to a fram oil filter?

According to the Fram Oil Filter cross reference guide, Kubota 66021-36060 can be replaced by Fram PH3682.

Why is there a squeaking noise when driving a Kubota rtv?

The squeak is caused by lack of lubrication to the steering bushing.

Pull the steering wheel off. There is a rubber bushing that surrounds the steering shaft. Remove the bushing with a thin screwdriver. Once removed clean the bushing and shaft. Then add anti seize lube to the shaft and and bushing. Then use a 7/8 " deep socket to drive the bushing back into the steering housing.

Clean and add anti seize lube to the bottom of the steering wheel . Then install the steering wheel.

How do you re-prime a Kubota b7100 4wd tractor that has run out of fuel?

1. Fill the tank with fuel, open the fuel cock. 2. open the bleeding screws at the top of the filter with 2 turns. 3. when bubblesdisappear from fuel coming out of the plug, tighten the bleeding screws. 4. open the airvent plug on the fuel injection pump. 5. pull the throttle lever completely to stop the engine, andstart the cell starter for about 10 seconds. 6. close the air vent plug when air bubbles disappear from the fuel flowing out. Good luck kingofmars@comcast.net

How do you put a drive belt on a Kubota t1460?

I need to know the number for the drive belt. The one that drives the tractor.

What type of Kubota engine is an F2803?

2800cc [2.8l] 5 cylinder direct injected naturally asperated diesel engine 49.5 hp

Cross reference Kubota oil filter hh164-32430 to fram filter?

I'm told a Fram PH8A is compatible... they are the same physical shape and size, but I havn't personally tried it on my Kubota yet.

Why will the power steering not work on Kubota tractor?

if the foot pedal is operated with the tractor off, the hydraulic fluid can leak back out of the power steering pump. work the wheel back and forth for a minute or two to get fluid back into the steering box. also, check the hydraulic fluid level.

AnswerThere is a brass connector between the hydraulic pump and the PS pump. This connector may have broken. or the end of shaft may have broken. This was the case with my L2250 DT