Local Area Network

The LANs themselves are no different depending on the number of hops. The number of hops to get to another LAN is based on the number of other routers the packet must pass through to get there. The LANs don't care about the difference between a single and a multiple hop.

The server knows by the destination port number, which attaches a listening program to a specific protocol.

IP address is categorized into IPv4 and IPv6. The IP is valid only if it is in the range of IP address range class.

If you question whether or not the IP is really that of a safe site, you can do an IP lookup using an IP lookup tool. They are available free and can be found by doing a search using the term "IP lookup."

I believe string length and cable length aren't 2 different things

I can't seem to get a answer

ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff:

The media access control protocol can be very simple

If the client doesn't know the IP address of the desired web server it has to find that out. This can be done via DNS if you know the name of the server as part of the URL.

After the address is located then transfer takes place using HTTP protocol. This is a layer 7 (application layer) protocol.

The Transport layer (layer 4) handles segmentation and reassembly of the data.

Ring Network Topology

There are a number of technical differences, involving the number of twists per inch on the conductors, the capacitance per linear foot between members of a pair and between pairs, and in the propagation speed of electricity along the cable. In practical terms, the category determines the fastest network that can use the cable at full speed.

Category 3 cable was originally used for telephone lines. It can be used with 10BaseT networks, twisted pair with a highest speed of 10 megabits per second (10Mb/s).

Category 5 cable has a guaranteed number of twists per inch on the two pairs (of four) that actually carry the data. It is rated to carry data on 100BaseT networks, up to 100Mb/s.

Category 5e cable has a slightly lower capacitance per linear foot, which results in its being able to handle data speeds up to 300Mb/s, and larger packets on 100Mb/s networks. It can be used on 1000BaseT networks, but most such networks will detect the lower-spec cable and derate themselves to 300Mb/s, and sometimes disable "jumbo packets", as the network hardware determines that the cable can't carry data at speed without corruption.

Category 6 cable has a higher number of twists per inch on all pairs, and a lower per-foot capacitance rating. It is able to carry data on 1000Base-T networks, up to 1000Mb/s, or one gigabit per second (1Gb/s).

There is, at this writing, no formal specification for Category 7 cable. In theory, it should be able to support 10,000BaseT, 10000Mb/s, 10Gb/s. However, there are few networks available yet that put 10Gb/s on copper, and there does not yet seem to be a standard for what sort of cables are needed to handle that data speed reliably.

A switch is useful only when you have more than 1 system to connect to a network or through a cable or DSL modem.

Packet switching is considered part of layer 3 of the OSI model.

Packet switching is considered part of layer 3 of the OSI model.

Packet switching is considered part of layer 3 of the OSI model.

Packet switching is considered part of layer 3 of the OSI model.

nbtstat

An octect is a byte with exactly 8 bits.

In order to name some options one would need to know the area - the question does not specify any.

how unblock my lan

A contention-based protocol (CBP) is a communications protocol for operating wireless telecommunication equipment that allows many users to use the same radio channel without pre-coordination. The "listen before talk" operating procedure in IEEE 802.11 is the most well known contention-based protocol.

Change the address of the one of the machines.

The IP address of course!

Think about it.

It's on the network layer, It is unique, and it's assigned to every device on the internet!

whiskers is the answer!!

It's 100 meters according to the specification. This is set as 90 meters for in-wall cable and 10 meters for patch cords.

You may be able to get the proper performance at longer distances, but even though the cable may perform at distances greater than 100 meters, the installation would still fail as 'out of spec.'

You can most likely find it within the monitoring services of your router.

The most common router administration page is:

192.168.0.1

192.168.1.0

192.168.1.1

If none of these, consider checking your router manual or on the router.

Most router admin logins are:

"No Username"

admin/password

-Or vice versa.-

The number of hosts in a classfull class A network with no subnetting is 16,777,214

they are:

1.unicast 2.broadcast 3.multicast

I am pretty sure that refers to the standard TCP, as opposed to some newer improvements, which are not yet commonly used.