The command access-list permit ip any any must be added to the last line of an access list to allow all other data packets to enter and exit the router.
What do you turn on to share a printer with network users?
If your printer is attached directly to your computer, you should share it (the way you do it depends of your operating system). If your printer is connected directly to your network (WiFi or Ethernet) it should be properly configured.
Metallic tape is any tape with an aluminum, steel or decorative foil on the outer surface. Steel tape s the general term for a steel tape measure or ruler or a metallic tape with a street foil surface.
What is the effect of configuring the ip bandwidth-percent eigrp command?
EIGRP will use up to 50 percent of the bandwidth of a link, as defined by the bandwidth interface configuration command. This command may be used if some other fraction of the bandwidth is desired. Note that values greater than 100 percent may be configured. The configuration option may be useful if the bandwidth is set artificially low for other reasons.
ExamplesThe following example allows EIGRP to use up to 75 percent (42 kbps) of a 56-kbps serial link in autonomous system 209:
interface serial 0
bandwidth 56
ip bandwidth-percent eigrp 209 75
The question is not complete. If you wanted to connect the two networks together you would need a gateway device.
What is the maximum length of SATA cable?
A standard SATA cable, per specification, can run up to 1m (3.3ft) of length without signal losses.
An eSATA cable can, per specification, run up to 2m (6.6ft) of length without signal losses.
Use the syntax:
route add xxx.xxx.xxx.xxx mask xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx
meaning:
route add (destination address) mask (subnet mask) (gateway)
For example, if you are on the 192.168.1.0 network with a gateway of 192.168.1.1 that is configured to access the 10.10.10.0/24 network, your statement would look like this:
route add 10.10.10.0 mask 255.255.255.0 192.168.1.1
Note: you need to add the "-p" switch to the statement in order for the route to stay after reboot. (route -p add 10.10.10.0 mask 255.255.255.0 192.168.1.1)
What is difference between GSR and CRS router?
These kind of routers are primarly used by Videotron (a french-canadian carrier), which means nothing more than just a brand of router from Cisco.
What protocol prepares data for transmission but has no resending capability?
UDP. User Datagram Protocol: A protocol that prepares data for transmission but that has no resending capabilities.
Peter Browning needs to step up to the plate and do big things. He needs to call up Bob White and have a little chat with him and Art Lawson about the future of White Cap. Then he needs to call a meeting between the department managers and explain to all of them that the company will be moving in a new direction with the blessing of Bob White and Art Lawson. He must explain that the change will be gradual, not drastic, but it will be definitive and in the best interests of the company. Browning must stress the importance of cooperation from all the department heads in order for the transition to be successful.
At this point he will be able to assess over the following weeks who is willing to assist in the cultural transformation at White Cap and who is a cancer to this effort for change. Then he can weed out the opponents of the changes and have the backing of true company patriots like Bob White and Art Lawson, who know he is acting in the best interest of the company.
The elimination of those opposed to the changes at White Cap will be a strong message, but the message will be that "those acting against the best interests of White Cap are no longer a part of our team". He could even start up some slogans like "White Cap: A great today, a better tomorrow." The only way to enact change in a traditional organization like White Cap is to stir up their patriotic loyalties to the company and convince them that these changes are truly better for the company and in turn themselves.
Which protocol is used to determine a MAC address of a remote host interface?
ARP (address resolution protocol) is used in this case. Basically, one computer asks, for example, "who has IP address 10.0.0.15" (the message is sent as a broadcast), and the computer with this IP address replies, including its MAC address.
ARP (address resolution protocol) is used in this case. Basically, one computer asks, for example, "who has IP address 10.0.0.15" (the message is sent as a broadcast), and the computer with this IP address replies, including its MAC address.
ARP (address resolution protocol) is used in this case. Basically, one computer asks, for example, "who has IP address 10.0.0.15" (the message is sent as a broadcast), and the computer with this IP address replies, including its MAC address.
ARP (address resolution protocol) is used in this case. Basically, one computer asks, for example, "who has IP address 10.0.0.15" (the message is sent as a broadcast), and the computer with this IP address replies, including its MAC address.
What is the port number for wwwaolcom?
An address does not define a port. Many kinds of communication could be directed to/from that address that would communicate on different ports. If you are asking about the port for HTTP protocol, it is port 80.
just restart
true
What is the difference between a core network and an access network?
core network is for swithiching of calls,routing,authentication,providing services like sms,prepaid,rbt etc but access network is used to provide network access to end users through wireless or wired medium
What is meant by a handshaking protocol?
When one computer1 connects to computer2, the first thing it has to do is contact computer2 and tell it who it is and that it wants to connect. Computer2 then must decide to accept (or deny or ignore) the connection and then tell Computer1 that the connection is accepted.
The protocol is just the series of technical rules that this basic process must follow. For example, when a tcp connection is initiated by compter1 the protocol is to send a SYN packet to a specific port on Computer2. Computer2 then, if accepting the connection, sends an ACK packet back to Computer1. From that point on the tcp connection is considered open and all future packets will have both the SYN and ACK bits until the connection is closed.
Do you want a high or low ping?
LOW ping. The lower the better
Ping is the delay between your commands and your players actions. So if you have low ping there will be a very short dalay but if you have high ping there will be a delay.