Mechanical Engineering

Do you burn gas when you run your air conditioning in your cae

in wire cut, a wire is passed through a metal or is placed next to it. the wire works as one of the electrodes while the work piece would be the other one; using andielectric liquid to isolate the wire from the work piece. the electricity is conducted in the wire. as the wire gets closer to the work piece the electricity (electrons) tend to jump from the wire to the work piece in order to create a complete electrical circuit that's when a spark is formed. the dielectric helps us by isolating the wire from the work piece as long as it can, so we can have enough difference in potential between two electrodes before the spark is formed, it works like capacitor stopping the current from going through it until it collapses at a potential and enough current passes through at once. A collateral effect of this passage of current is that material is removed from both the electrodes.

Beveling is done to proved an smooth tapered edge. This will be done to an edge for the sake of safety or to decrease the amount of wear on the surface.

The job of a mechanical engineer is to design machines and mechanical installations for major projects. They also evaluate installed equipment, processes and products.

Slam Shut-off valve is installed immediately after the filter & prior to the Regulator. It normally remains open, incase the outlet pressure of the regulator exceeds the permissible limits, the slam shut off the valve senses it through the impulse line & immediately shuts off the flow to the downstream. When the regulator is repaired, the slam shut off is to be open manually by pulling the knob. Once the flow starts through the shut off valve it will remain open till the outlet pressure of the regulator is within limits.

Spring steel chemical composition

GRED

CARBON

SILICON

SULPHUR

PHOSPHORUS

SULPHUR PHOSPHORUS

COPPER

MANGNESE

1

0.50/0.70

0.15/0.35

0.05 MAX

0.40 MAX

-

0.20

0.30/1.00

2

0.60/0.80

0.15/0.35

0.04

0.04

-

0.50

0.80 MAX

3

0.75/1.00

0.45/0.35

0.03 MAX

0.03 MAX

0.05 MAX

0.12

0.80 MAX

4

0.75/1.00

0.15/0.35

0.25

0.025

0.004

0.12

0.80

0,32-0,36

Agricultural mechanization is the use of mechanical technology and engineering in the field of agriculture. Most of these technological advances are meant to increase efficiency in agricultural work, reduce the stress and pressure on farmers and even reduce long term costs.

Corex is a smelting-reduction process developed by Siemens , for the cost-efficient and environmentally friendly production of hot metal from iron ore and coal. The process differs from the conventional blast furnace route in that non-coking coal can be directly used for ore reduction and melting work, eliminating the need for coking plants. The use of lump ore or pellets also dispenses with the need for sinter plants. All metallurgical work is carried out in two separate process reactors - the reduction shaft and the melter gasifier. Lump ore, sinter, pellets or a mixture are charged into a reduction shaft where they are reduced to direct-reduced iron (DRI) by a reduction gas. Discharge screws convey the DRI from the reduction shaft into the melter gasifier where final reduction and melting takes place in addition to all other metallurgical and slag reactions. Corex is a smelting-reduction process developed by Siemens , for the cost-efficient and environmentally friendly production of hot metal from iron ore and coal. The process differs from the conventional blast furnace route in that non-coking coal can be directly used for ore reduction and melting work, eliminating the need for coking plants. The use of lump ore or pellets also dispenses with the need for sinter plants. All metallurgical work is carried out in two separate process reactors - the reduction shaft and the melter gasifier. Lump ore, sinter, pellets or a mixture are charged into a reduction shaft where they are reduced to direct-reduced iron (DRI) by a reduction gas. Discharge screws convey the DRI from the reduction shaft into the melter gasifier where final reduction and melting takes place in addition to all other metallurgical and slag reactions.

no1:diamler

no2: Volvo

.

.

no5: tata motors.... proud to be Indian...

i dunno about the others....

rony.

Container ships are some of the largest ships to cross the oceans. The function is to transport goods from one location to another. The reason containers are used is because the containers can be loaded and unloaded extremely efficiently and shipped with relative ease.

It works simple. You pull the trigger.

Amount of heat required to Melt a Ton of Ice in a 24/h Period This converts to about 12000btu/h.

It is the housing standard on a motor

Totally Enclosed Fan Cooled

Stress is a tensor because it affects the datum plane. When this is affected and it changes, it is then considered a tensor.

Isometric drawing paper either has dots on it with very minimal distance in between them, or has very small triangles or diamond shape with no distance in between them. It is available in different sizes and varieties.

a directional advantage

20percent 60percent you find the one

flooded type cooler is a cooler that is being flooded while direct expansion type is a type that is being directly expanded.

23 degrees 23 degrees 23 degrees

Mine did the same. The rubber gasket under the valve knob had become messed up. I unscrewed the valve and put the gasket back in place. My local pool place says this happens alot when you turn the valve from backwash to filter while the pump is running.

Quadro family+ fx 4400+fx 3400

Compressor variable vane control regards the ability to alter a turbine's fin geometries position ranging from open to closed positions. By mechanically and pneumatically actuating (controlling) these geometries power outputs can be operator managed.

In seating and fuselage terms, the Airbus A380 is the largest plane. The Boeing 787 Dreamliner is second.