0
Can you do a front right wheel bearing on 91 topaz myself without any special tools?
Wiki User
∙ 17y ago
there are no front wheel bearings in front wheel drive cars To correctly answer your question yes, there are front wheel bearings--in fact I am going to have to have mine replaced. In the Mercury Topaz book from Haynes they do not reccommend that you do them yourself. I'm thinking that a special press is used for it. Puglet
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
When a cold front or a warm front stays in place for several days without invading another front?
Stationary front.
What happens if someone hits the car in front of them and the front driver has no license?
The front driver can be arrested for driving without a license, since it is a federal offense.
Which special effect technique is being used in television weather reports in which meteorologists stand in front of moving maps?
Blue board
How do you replace the front wheel bearings in a 1992 Mercury Topaz?
start by taking the wheel off then take off the caliper. After take the rotor off. Then there is a nut with a pin through it, take the pin out and undo the nut. Now the hub will come off and one bearing will come out. With a hamer and a punch drive out the other bearing and the grease seal. You should change the races as well(the serface the bearings ride on inside the hub. You will meed it buy wheel bearing grease and pack the new bearings with grease. You can never use enough grease the more the better. Repeat the process in reverse to reinstall. If you have any more Questions E-mail me at reese_koch@hotmail.com
How do you know which outlet a wall switch controls?
Plug something into each and see which one it is. This is most often in the front room of a house and I would guess either the front center one possibly under a front window or in the corner furthest from the switch. It could be any in the room and there is really no way of knowing without testing each plug.
How do you change the front wheel bearings on a 1996 Chevy Beretta Does the procedure require special tools and are the bearings a sealed unit and have to be replaced with the rotor also?
Replacing front wheel bearings on a front-wheel drive vehicle requires a good knowledge of vehicle service. Normally, you do not need special tools, but there is a special procedure for removing and re-torquing an axle spindle nut. Never reuse a spindle nut!!!! The bearing will be a unitized one-piece bearing, and the brake rotor is not part of the bearing. It can be removed after removing the brake caliper.
What Front Bearing pack compatible with 1990 S10Blazer?
It is very hard to figure out how to replace a bearing pack without extensive knowledge. However, if you contact a professional, they can help assist you.
How do you change front wheel bearing on fiat stilo?
dont know but mines shot and would be usefull to know if its possible to do myself to save a few sponders? sound!
Does changing a front wheel bearing on a 2004 Chevy Silverado 1500 require a special tool?
yes,it requires two special sockets for the inner and outer wheel nuts inside the hub
How to change front wheel bearing on fiesta?
To replace the front wheel bearing on a Ford Fiesta, you will need to remove the wheel. Then with a hammer you can pull the old bearing out.
How do you change front wheel bearings 2001 Toyota Corolla?
can you grease the front wheel bearing s on a 2001 toyota corrolla without removing them. Is there a external greaese fitting.
How do you change front wheel bearing in 2003 Kia Sorento?
how do i change front wheel bearing of kia sorento 2003
How do i change the bearing on a 1996geo tracker front of a 4 wheel drive?
how do I get to the front bearing on a geo 4 wheel drive
How do you replace front wheel bearing on 1996 Hyundai Elantra?
how to replace front wheel bearing on 1996 Hyundai elentra
Change 1998 jimmy 4x4 front wheel bearing?
How do you change a 1998 jimmy 4X4 front wheel bearing ?
How do you pack Chrysler 300m front wheel bearing?
It is a sealed bearing and can not be repacked.
Is the front wheel bearing in the hub assembly of a 2001 Honda V6 accord a separate unit or is it pressed in?
just replacd myself. it is pressed in. it will actually come out however it needs to be pressed back in.
