Seat Belts and Safety Systems
Spark Plugs and Wires
Chevy Corvette
Grand Prix SE

Can you replace lap belts on a 1976 Corvette with shoulder belts?

152153154

Top Answer
User Avatar
Wiki User
Answered
2009-06-29 22:48:51
2009-06-29 22:48:51

Yes you can. I purchased a rebuilt set from Davie's corvettes parts and accessories in 2004. They cost me about $400.00. The old pullies are removed from under the seats and from behind the shoulders of the driver and passenger seats. The car will have manufactured holes in the body to insert the bolts through. Good luck Correct. They're available from almost any Corvette specialty supplier, not just Davie's. I would NOT recommend a used set, EVER, since you really don't know exactly what kind of shape the mechanisms are in. -ku2002 1976 Corvettes came from the factory with shoulder belts, FYI. Anyhow your old ones can be restored to factory new condition by a company called SSnake Oyl. --Dave.

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


Yes, the '76 came standard from the factory with shoulder/lap belt combo. Top part bolts into pillar and bottom bolts in right by the seat mount. Good luck! -ku2002 Yes, 1976 Corvettes did not come with lap belts only. They were equipped from the factory with shoulder belts. (Or the shoulder/lap combo) mentioned above. But it wasn't an either/or deal. Plain lap belts were never installed in 1976 Corvettes.


Will a 1976 Corvette C3 Hood fit on a 1978 Corvette C3.


it will most likely be easier to just replace the pump all at once


hwere can I get the schematics for all the body bushings on a 1976 Corvete?


Remove all the screws, take the arm rest off, and lift.


1976 top will not work on an 81' The latches are different.


The "StingRay" designation was dropped from the Corvette after 1976.


Corvette Specifications 1953 - 1982 http://corvette-world.com/corvette_specifications.php


look in the haynes manual for that year corvette


No, the last year for the Corvette to be called a Stingray was in 1976.


A Corvette that was built in late 1976 up to late 1977.



Yes, the crossmember for suspension is in front of the engine. Very easy job.


What about it? Has four total.



my 1976 corvette is supped up and she will run a solid 165 it will probably do more but i dident want to push it cause the nose was coming off the ground


The hood for a 1976 Corvette is not the same dimensions as a 1980 despite their similarities. Modifications can be made to the hood to make it work but it will not look factory.


the nova never had a serpentine belt in 1976, it had 2 belts on it unless it had air conditioning and then it had 3 belts.


NO. Do not attempt to do so, as the bumper will be extremely unstable.


ANSWER: Well, go buy a new one, paint it to match the color of the car, unbolt the old one and bolt the new one in. There.


Put a jack under the engine for stability. Unbolt one motor mount, and jack the engine up slightly. The mount should be able to be removed, replace it and repeat for the other side.


Approx 3445, options vary weight


Yes, the same frame and basic underpinnings were used for that whole generation. The C3 (1968-1982).


maybe you can unbolt the universal joint and then slide it out of the spline


it should as 76 corvettes had no horsepower whatsoever.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.