answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2005-05-01 14:04:45

connected to trans

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

How do you bypass the heatercore on a 1997 sunfire gt?

connect a piece of heater hose from the thermostate housing (where one of the hoses connected to from the heater core already is) to the connector for the coolant at the bottom of the enigine (where the second line should be connected).


Is there a ground wire connected to the transmission?

yes theres an braided ground wire that bolts to the transmission bell housing


Where is the flywheel located on a camaro z28?

On the back of the engine, mounted between the engine and transmission, inside the bell housing. You cannot see the flywheel. The starter is connected to the flywheel when you start the engine.On the back of the engine, mounted between the engine and transmission, inside the bell housing. You cannot see the flywheel. The starter is connected to the flywheel when you start the engine.


Where is the transmission housing for 1991 ford E350?

The transmission housing for a 1991 E350 is bolted to the rear of the engine. The entire transmission case is considered the housing.


Where is the starter at on a 1998 Chevy Cheyenne 350?

Bottom of the engine, passenger side, connected between the engine and transmission bell housing.


Where is the starter on 1993 Mazda mx3?

Under the intake manifold. The starter is connected to the bell housing on the transmission and is held on by three bolts.


Were is the starter on a 94 Ford Explorer?

connected to the transmission bell housing on the right side, have to look from underneith the vehical, easy to take out if u have the tools


Where is the crank position sensor on a dodge grand caravan 3.3L?

It is on the top rear of the transmission bell housing.It is on the top rear of the transmission bell housing.


Where is the location crank sensor for 2001 dodge grand caravan?

Top rear of the transmission bell housing.Top rear of the transmission bell housing.


Where is a crank sensor located for a chrysler sebring 1996 2.5?

It is on the top rear of the transmission bell housing.It is on the top rear of the transmission bell housing.


Where is the crank sensor on a 1999 Chrysler Sebring coupe 2.5L V6?

It is on the top rear of the transmission bell housing.It is on the top rear of the transmission bell housing.


Where is the bell housing on 1999 dodge ram truck 5.2L?

The bell housing is the front of the transmission, the end that bolts to the engine.The bell housing is the front of the transmission, the end that bolts to the engine.


The clutch went out in your 2001 eclipse gt and you can't get the transmission to break free from the bell housing Any suggestions?

why would you want to braek the bell housing free from transmission ? the bell housing needs to be removed to replace clutch, so remove bell housing and transmission as one unit.make sure starter motor is removed. usually blts the secure bell housing and transmission toether can only be reached from inside bell housing after bell housing and transmission are removed from vehicle


Will the bell housing detach from the transmission in a 1997 Ford Taurus?

The automatic transmission housing / case is a single casting, so the bell housing cannot be detached separately.


What is the difference between an intigrated bell housing and the non intigrated bell housing for a 5 speed manual transmission on the 1994 Chevy 4x4 diesel pick up?

An integrated bell housing means it is part of the transmission assembly and can't be removed from the transmission. A non integrated bell housing allows the end user to remove the housing from the transmission usually by unbolting it.


Where is the bell housing on a 1992 Ford Ranger?

The bell housing is the front of the transmission ( the larger diameter portion ) where the transmission is bolted to the engine


How do you line up 1990 Jeep Wrangler bell housing to transmission?

If a manual transmission, you need a clutch alignment tool. It lookslike the front shaft of your transmission, is generally made of plastic and is used to align the disk when tightening up the pressure plate. You should be able to buy one at any auto parts store.


Is it possible to use the bell housing from an avenger 6 cylinder AT on a 4 cylinder MT and use it on the 6 cylinder engine?

The bell housing does not come off of the automatic transmission.The bell housing does not come off of the automatic transmission.


Automatic transmission serial number location 2006 Honda civic?

Automatic transmission serial numbers are found on the front of the housing. It will be displayed on a barcode that will be inlayed on the transmission housing.


How do you remove fourrunner transmission?

You'll have to disconnect the driveshafts, the shift linkage, the speedometer cable, and the clutch (if it's a manual). Then you place a transmission jack centered under it, secure the transmission to the transmission jack, and unbolt the bell housing from the engine block. If you can't access the bolts for the bell housing with the transmission attached, then you'll have to separate the transmission from the bell housing.


Will it hurt the transmission if you don't fix the speedometer?

No. Several Things Go Wrong With Speedometers. Cable Break, Plastic Gear In The Back Of Speedometer Housing, Or In The Housing Of The Transmission. But No It Will Not Hurt The Transmission.


Where is the transmission solenoid on a 1995 Chevy beretta?

inside the transmission bell housing


1999 sentra starter?

The 1999 Sentra starter is located right beside the transmission bell housing. That is the housing where the transmission bolts up to the engine.


Where is the speed sensor on a 1991 Ford Escort 1.9 manual transmission?

It is on top of the transmission under the intake housing. Take the housing off to get to it. It is held into the transmission by a clamp bolt. Not hard to get off.


How do you get transmission out of 98 blazer?

You'll have to disconnect all cables and wires from the transmission and transfer case (if applicable). You'll need a transmission jack. First, you disconnect and remove the driveshafts. How you proceed from there is up to you. You can remove the bell housing, transmission, and transfer case (if applicable) as a single unit if you have an adequate transmission jack to do it. Or, you can remove the transfer case, then the transmission, then the bell housing. However, then you replace the transmission, you'll want the bell housing to already be mounted to the transmission.