Auto Parts and Repairs
Fuel Pumps
Ford Taurus
Ford Ranger

How can you fix the switch for the moonroof after it has been pushed up into the housing on a 1993 Ford Taurus SHO?

545556

Top Answer
User Avatar
Wiki User
2015-07-15 18:26:21
2015-07-15 18:26:21

The same thing happened to my 95 SHO. What I did to fix it is glue the part of the switch that is supposed to remain still back into place using "Automotive Goop." That's the real name of the stuff, I got it from AutoZone. I spread a small amount up and inside the floor of the housing and on the part of the switch that is supposed to be secured. You can tell what parts are supposed to touch the floor of the housing by trying to pull the switch down through the hole. Be sure to use glue on every part that is supposed to remain still on the housing. I then fed the switch back down through the hole in the housing and held it there with my fingers for a few minutes to let the glue set. Waited a few hours before using the switch again and it works fine and the glue has stayed for at least a year now. Sorry for my terrible explanation, if you need a better description feel free to email me.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

1998 Taurus pressure sensor location; It is located on the firewall side between the head and the transaxile housing.

User Avatar

probably water intrusion in your switch assy.

User Avatar

The switch is on the back of the block near the transmission housing drivers side firewall side.

User Avatar

I have a 96 Ford Taurus and need to get the key switch out. Please help.

User Avatar

Take vehicle to car dealership for repair, switch is broken. replace switch is approx $650

User Avatar

The signal light switch is part of the multifunction switch on the steering column.

User Avatar

The heater switch is located in the middle of the car in the 1998 Ford Taurus. It is either above or below the radio.?รฆ

User Avatar

you can't crank it shut, the motor is electronically worked by a switch. You will probably need to replace the switch or the moonroof motor is no longer good.

User Avatar

On a 2002 Ford Taurus : The fuel pump shut off switch ( inertia switch ) is on the passenger side of the trunk , behind the trunk liner ( there is an access hole )

User Avatar

On a Ford Taurus : The multifunction switch is INSIDE the steering column cover The turn signal lever and hazard flasher button stick outside of the cover

User Avatar

a switch that is trigered to light up the light when the brake pad is pushed in

User Avatar

To replace the headlight switch in a 66 mustang, you first have to remove the instrument cluster housing. After you have that out of the way, you will see a small button on the housing of the switch mechanism itself. Pull the switch knob all the way out, as if turning on the headlights, then push that little button and the switch stalk will pull all the way out of the switch housing. Then unscrew the switch bezel, pull the switch housing back, so that it clears the dash, unplug that big wire connector from the side of the switch, and remove the switch entirely. To install the new switch, you just do what you just did, except do it backwards.

User Avatar

There is a spring clip under the front of the switch. Push a thin blade between the front of the switch housing and the roof padding and you can pull the front of the switch down. The housing should pull out forward as the back of the housing is held up by a plastic tab.

User Avatar

On a 1999 Ford Taurus : Yes , the fuel pump shut off switch ( inertia switch ) is in the trunk , on the passenger side of the trunk , behind the trunk liner ( there is an access hole )

User Avatar

look at the housing where the lower rad hose connects to a small switch in this housing is what you are looking for

User Avatar

On a 1998 Ford Taurus : The fuel pump shut off switch ( inertia switch ) is located in the trunk , on the passenger side , behind the trunk liner ( there is an access hole )

User Avatar

The price for an ignition switch for a 2000 Ford Taurus is around $60.00. Installation for an ignition switch will typically take between 60-90 minutes. Labor costs will run around $100.00 for installation.

User Avatar

WLAN switch locationFor the PSPgoThe WLAN switch is on the left side and pushed up to be turned on.For the PSP-2001 and PSP-3001 seriesThe WLAN switch is labeled WLAN. It is located on the top of the unit to the left of the UMDTM door and must be pushed to the right to be turned on.For the PSP-1001 seriesThe WLAN switch is on the left side and pushed up to be turned on.

User Avatar

the relace switch by the pedels that says hood or a picture of a hood look

User Avatar

The combination neutral start and backup light switch is mounted inside the shifter housing. Remove the screws holding down the shifter housing and remove the switch. Adjust the switch by moving it on its mounts.

User Avatar

On the right side of the steering wheel.

User Avatar

Door Switch Fault You may find the door-switch is the problem, it is quite common on that model and age, the door hinges wear and the door drops, so the switch is not being pushed in fully, which would break the circuit and put the light out, [try adjusting the door to make it fit better, or replace the hinges], [the switch may be loose or broken], [there is one switch on each door].


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.