turn key to on position w/ engine off and press gas pedal 5 times fast and watch for oil light to blink 5 times and then it's reset
There may be a red reset button on the fuse panel in the side of the dash down by the driver-side door. With the key in the on position, but the car not running, push the reset button once, then the change oil light will start flashing, then press an hold the reset button for a few seconds and the light should go off. This worked for my 2000 Grand Am, not sure if its the same for the 2006 models.
how do you reset change oil light on chrysler grand voyager minivan 1997
The car actually measures the viscosity of the oil while you are driving and running the car when you change the oil the light will be reset.
In order to reset the oil change light on a 2006 Hyundai Tuscan you need to take the car to the dealership or your local oil changing station.
How to reset service light on a 2004 grand am
http://www.gminsidenews.com/forums/f53/98-grand-prix-change-oil-light-stuck-59318/ For a 98 but same process.
After changing the engine oil, the system must be reset. With the ignition key to ON (engine not running), push the RESET button located in the driver's side instrument panel fuse block. The CHANGE OIL light will start to flash, press and hold the RESET button again. The reset is complete when you hear the chimes and the CHANGE OIL light goes out.
Just changing the oil doesn't do anything to the gauge, hold reset button down until readout changes change the oil
Reset the change oil light on Mazda 3
yes you can, just look in your manual for proper procedure and you are set.
Turn the key on. Depress the gas pedal and release 3 times slowly. Should reset it.
Check engine light is reset with a scan tool.Oil change due is reset by pressing "step" until "0 miles to service" is displayed. Then press and hold "reset" until it resets.
To reset the service light on a Grand Scenic 54 the engine's computer should be reset. An easy way to reset the computer requires unplugging the battery for 5 seconds. The computer will then reset.
how do you reset change the oil light in a 2004 alero?
To reset the light, turn your ignition to on, then press the gas pedal 3 times, then start the car. To reset the light, turn your ignition to on, then press the gas pedal 4 times then you will hear a beep, then start the car.
Have the SRS repaired by a qualified technician and they will reset the light.
On your overhead console, hit "Step" until you see the miles to serice. Then you just hold your reset button and it will change to 3000 miles
The ABS light on a 2004 Pontiac Grand Am can be reset by connecting an OBDII code reader to the vehicle's computer. It can reset all codes and determine their cause.
take it to a good mechanic or a ford or merc dealer and they have to clear it for you
YOU HAVE TO RESET IT SOMETIMES 4-5 TIMES .YOU NEED YOUR MANUEL TO DO IT.
To reset the change oil light on a 2008 Mitsubishi Lancer after changing the oil, a person can turn the key to on, but not start, and pump the gas pedal three times, then turn the key off. If this method does not work it is possible to disconnect the battery for a few minutes, then re-connect it.
Because you need to reset the light after you change the oil. Changing the oil doesn´t turn off the light automatically , you need to reset it. there is a very small push button on the dash board that has a label "RESET OIL CHANGE", with the engine off, push and keep pushing while you turn the key to power up the accesories but don´t turn the engine on. the light will go off after a second or so. Because you need to reset the light after you change the oil. Changing the oil doesn´t turn off the light automatically , you need to reset it. there is a very small push button on the dash board that has a label "RESET OIL CHANGE", with the engine off, push and keep pushing while you turn the key to power up the accesories but don´t turn the engine on. the light will go off after a second or so.
turn the ignition to "Run" or where it would be once it was started, but dont start it. quickly push the gas pedal to the floor three times. the change oil light should start flashing and it will reset.
how do you reset the tire pressure warning light on a 2004 pontiac grand prix
The transit brake warning light, on a Ford, can be reset by changing the brake pads. If the warning light is still on after changing the brake pads remove the fuse for 10 seconds.
The light will reset itself when the cause of the code has been repaired.