Dodge Ram
Toyota 4Runner
Toyota Camry
Toyota Tundra

How do you disable the the automatic door lock on a 2000 Dodge Ram 2500?

272829

Top Answer
User Avatar
Wiki User
2008-11-21 17:52:30
2008-11-21 17:52:30

Check the owners manual in the section where it describes the automatic locks. For example, in the 2004 Dodge Ram 2500 users manual it indicates the automatic locks can be disabled by turning the ignition key on/off 4 times (do not start the vehicle), leave the ignition in the on position and move the lock switch in the unlock direction. You will hear an audible beep that indicates the automatic lock function has been disabled. To re-enable automatic locking, repeat the previous procedure. If you cannot find information in the owner's manual, call your local dealership for instructions. In many cases it is possible to reprogram car and truck functions without visiting the dealer.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

It will be on the side of the automatic transmissions.

User Avatar

This process can be complicated, but it is listed in your owner's manual.It would be easier if you had someone to read the instructions to you while you do it.

User Avatar

You will need a trans, wiring, computer, steering column, and trans cooler from an automatic truck

User Avatar

Manual, yes.Automatic, no. The control systems are differentManual, yes.Automatic, no. The control systems are different

User Avatar

Reman will be around 2000-2500 for the partReman will be around 2000-2500 for the part

User Avatar

Why would you want to do such an ignorant thing?

User Avatar

The automatic is called a 46re. The manual is a nv4500.

User Avatar

The automatic is a 47 RE. The manual is a NV4500.

User Avatar

Automatic is a 68rfemanual is a g56Automatic is a 68rfemanual is a g56

User Avatar

Stock an automatic is 195 hp a manual is 215 hp.

User Avatar

The belt has an automatic spring tensioner and can not be "tightened".

User Avatar

The automatic is a 47RE. The manual is a NV4500.

User Avatar

The automatic transmission behind the Cummins engine in a Ram 2500 is a Chrysler transmission. Depending on the year it could be a 47rh, 47re, 48re, or a 68rfe.

User Avatar

The throttle position sensor on a 2000 Dodge Ram 2500 Diesel is located on the right hand side of the carburetor. This location is on the driver's side of the motor.

User Avatar

i have a 2000 dodge ram 2500 quad cab and cant figure out how to adjust rear doors to be a little more tight. thank you,72fj

User Avatar

When repairing a car it is important to know the costs of the repairs. To rebuild a 2500 Dodge Transmission it could cost between $2000 and $4000.

User Avatar

On my 2000 Dodge 2500, there is a fuse box under the hood, and the fuse is a blue 20 amp.

User Avatar

The payload capacity for the 2000 Dodge Ram 2500 diesel 2x2 with the long bed is 3550 pounds. This is the largest payload capacity for this series of vehicle.

User Avatar

A retaining clip holds the ignition switch in place on the back of the ignition cylinder on your 2000 Dodge Ram.

User Avatar

Dodge does not use inertia switches. The fuel system is computer controlled with relays.

User Avatar

It is on the top of the bell housing, behind the passenger side head, hiding under the transmission dipstick.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.