Loosen the tensioner pulley. Put the belt around the alternator pulley and the tensioner pulley. Move the tensioner pulley to the right until the belt is tight. Tighten the tensioner pulley.
You should not have removed the tensioner to install the belt. It has a pivot point that and can be moved in order to release the tension on the belt. Once you install the new belt, leave it off the tensioner until last, pivit it and install the belt oner the tensioner.
You will need to loosen the tensioner pulley. When the tensioner pulley is loose the air conditioning compressor belt will become loose. Put the new belt on and tighten the tensioner pulley.
there is no repair for a belt tensioner. just buy a new tensioner. remove old belt, remove old tensioner, it is held on with one bolt. install new tensioner. install new belt
The belt tensioner is self-adjusting.
In order to put in a new belt tensioner in a 1992 Plymouth voyage you must first release the belt from the stock tensioner and remove. Next install the new belt with the stanchions given.
# Install belt on to all pulleys except belt tensioner # Using the extension insert it into the belt tensioner and push away from you.Carefully install the ribbed belt on the tensioner and slowly allow the extension to move toward you as tension is placed on the belt # Remove extension from belt tensioner and inspect the belt to be sure it is seated correctly on all the pulleys if not remove belt and reinstall
Begin by loosening the tensioner pulley. Take the old air conditioning drive belt on. Put the new air conditioning drive belt on and tighten the tensioner pulley.
belt tensioner fell off this morning.I need to know how to install new one.
it has a manual tensioner
To re-install a belt tensioner for a 1987 Ford Taurus, tighten the bolt when the tensioner pulley is holding the serpentine belt tight. The belt tensioner sits in a slot and can be adjusted to hold the belt tight.
How do you change the supercharger belt tensioner in 1997 Pontiac Grand Prix GTP?
You have to install a new belt tensioner.
Pull on the belt and you can see how the tensioner moves. Put a wrench on the bolt.
You cannot adjust the belt tension on a 2000 dodge grand caravan. This vehicle is equipped with an automatic tensioner. If tensioner is frozen or will not hold the belt tight, it must be replaced.
look how it is routed before removal. There is a tensioner that holds the belt tight. Use a wrench to hold the tension off the belt while you pull the out from under the tensioner. install new belt the same as old.
You have to remove the belt first, this is easiest with a tensioner tool. Then the nut that holds it to the bracket is on the backside of the tensioner and needs to be done from the bottom.
Usually you relieve tension on the tensioner pulley by pulling it to the left or right.
Loosen the tensioner pulley. Remove the old drive belt. Install the new drive belt. Tighten the new drive belt with the tensioner pulley.
You will need to loosen the tensioner pulley on your 1994 Pontiac Grand Am. The old serpentine belt will come loose and can be removed. Put the new serpentine belt on and tighten the tensioner pulley.
Pull back the belt tensioner and slip the belt off. Reverse procedure to install.
If you are refering to the belt tensioner. I have not seen one on a grand wagoneer with a 360.
== # Loosen the idler pulley lock nut # Turn the adjusting screw to lower the idler pulley # Remove A/C belt. == # Install A/C belt over pulleys. # Apply a snug torque to the idler pulley lock nut. # Turn adjusting screw until proper belt tension is obtained. # Tighten idler pulley lock nut to 54 NÂ·m (40 ft. lbs) == The Poly-V generator/power steering pump belt is provided with a dynamic tensioner. == WARNING: DO NOT ALLOW DRIVE BELT TENSIONER TO SNAP BACK, AS DAMAGE TO TENSIONER AND/OR PERSONAL INJURY COULD RESULT. # Remove air conditioning belt. Refer to procedure in this section. # Apply a force in a clockwise direction to the tensioner pulley bolt # Remove belt. == # Install belt over all pulleys, except for the tensioner pulley. Refer to for belt routing. # Apply a force in a clockwise direction to the tensioner pulley bolt # While holding tensioner, position belt over tensioner pulley. # Slowly release force on tensioner. # Verify belt is properly routed and engaged on all pulleys.
Begin by removing the serpentine belt from your Oldsmobile Cutlass. Remove the tensioner pulley retaining bolt. The retaining bolt will be in the center of the pulley. Reverse the process to install your new belt tensioner.