answersLogoWhite

0


Best Answer

Take the door panel off, remove the moisture barrier and access it from the inside of the door. Should be a large metal clip holding it on to the door. Of course, you'll have to disconnect the lock rod from it too.

User Avatar

Wiki User

โˆ™ 2007-09-07 03:44:52
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove a lock cylinder from a 1994 Geo Prizm?
Write your answer...
Submit
Related questions

How do you remove the ignition lock cylinder on a 1994 Grand Am?

The 1994 Pontiac Grand Am ignition lock cylinder is held in place by the retaining ring at the top of the cylinder. Remove the retaining ring. Remove the wiring harness from the back of the cylinder.


How do you remove and replace an ignition lock cylinder on a 1994 Ford Bronco?

Begin by removing the retaining ring at the top of your 1994 Ford ignition lock cylinder. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the ignition lock cylinder. Reverse the process to install your new ignition lock cylinder.


Can you replace the ignition lock cylinder on a 1994 Pontiac firebird without removing the steering wheel?

You can replace the ignition lock cylinder in your 1994 Pontiac Firebird without removing the steering will. Remove the retaining ring at the top of the ignition cylinder. The ignition cylinder will slide out.


How do you remove ignition lock cylinder from a 2000 ML430?

Remove the retaining ring from the top of your 2000 Mercedes-Benz ignition lock cylinder. Slide the ignition lock cylinder out and remove the wiring harness.


How do you change door lock tumbler?

To change a door lock tumbler, remove the deadbolt and extract the lock cylinder. Turn the lock cylinder over and remove the plug from the cylinder. Replace with new tumbler.


How to replace a 1997 geo prizm lock?

If you mean the door lock cylinder...remove the interior door panel. On the back of the door handle there are 2 10mm hex bolts. To the outer edge of the door there is an access hole. With an extension, remove the 10mm bolt that holds the lock cylinder and door handle together. Reach in and push the nylon retainer that holds the rod into the cylinder (yellow on driver side, white on passenger side) and remove it. A slight twist of the cylinder will remove it from the door handle. Replace in reverse order.


How do you remove the ignition lock cylinder on a 1997 astro van?

Remove the retaining ring, from the top of your 1997 Ford Astro ignition lock cylinder. Remove the wiring harness from the back of the ignition lock cylinder.


How do you remove the lock in the cylinder on a 1986 Mazda B2000?

what lock cylinder?door or ignition? door is simple, remove inner door panel, unhook rods attached to lock cylinder, remove retaining clip


How do you remove the ignition lock cylinder from a 1994 Ford Thunderbird with out a key?

rip it out or call a locksmith it happened with my 94 tbird


How do you replace an ignition lock cylinder on a Chevy S-10?

Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.


Why must a plug in a mortise cylinder lock be turned slightly before removing it from the cylinder?

You turn a mortise cylinder lock slightly before removing to release it from the lock housing. There is an obstruction in the lock design to keep the cylinder more secure in the lock. After you remove the holding screw from the lock body you can turn the cylinder slightly to release it and remove from the lock housing. Not all mortise cylinders are designed this way. Some of the cylinders unscrew from the lock housing after releasing the cylinder retaining screw.


How do you remove the door lock on 2000 dodge neon?

how to remove a door lock cylinder on 2000 dodge neon


How do you replace lock cylinder mustang?

If you are talking about the ignition lock cylinder, turn the key to the accessory position, insert a paper clip into the little hole on the face of the lock cylinder to release the lock pin, turn the key a little further in a counter clock-wise direction and the lock cylinder will pull out. If you are talking about a door lock cylinder, remove the door panel, roll the window all the way up, pop the little clip loose on the lock rod that is hooked to the back of the cylinder and remove the rod from the lock arm, then pull the 'C' clip out that is holding the lock cylinder in place and push the lock cylinder out.


How do you remove the ignition lock cylinder on a 1973 Firebird?

pull steering wheel off, remove the steering lock disc, then remove the signal light switch assembly to gain access to the retaining screw that holds the lock cylinder in place,


How do you remove the ignition switch cylinder to replace it on a 1976 Chevy truck?

Remove the steering wheel then the lock plate then the turn signal switch. You will then see a screw close to the side of the lock cylinder. Remove this screw and pull the lock cylinder out. It takes a special tool to remove the lock plate and you can rent then at some parts stores although they aren't very costly.


How do you remove a lock cylinder for a 1988 gmc jimmy?

if it is the ignition lock cylinder, first disconnect the battery, you need to remove the steering wheel ,turn signal switch , etc, then you need to insert the ignition key into the lock cylinder, turn it to the run position,then pull the cylinder out, reverse the operation to install the cylinder,


How do you remove the ignition switch from a 1988 Dodge Ram 50?

Ignition switch and lock cylinder removal 1988 Dodge Ram 50.Disconnect the negative battery cable from the battery.Remove the steering column cover to gain access to the ignition switch/lock cylinder.Using wire cutters, remove the cable band.Remove the bolts that hold the ignition switch/lock cylinder to the steering column.Unbolt and remove the key reminder switch and remove the switch lock cylinder from the steering column.


How do you remove the ignition lock cylinder from a 1994 Ford Ranger?

do you have the key!!!! remove the steering wheel covers turn the key to run there should be a little brass pin under the lock cyl push it in and pull out cyl if no key you have to drill out the tumblers.


How do you replace the ignition lock cylinder on 93 Chevy 3500?

Pull the steering wheel with a puller tool, remove the lockplate with a lockplate tool, remove the turn signal assembly, remove the hazzard switch, remove the brass connector, remove the lock cylinder.


How do you change the ignition lock cylinder in a 2001 Chevrolet Tracker?

To change the ignition lock cylinder in a 2001 Chevrolet Tracker, first disarm the air bag system. Then remove the clock spring assembly to be able to remove the old ignition lock cylinder and replace with a new.


How do you remove the glove box lock on a 1935 Chevy Master?

lock has to either opened with a key or picked to open position, then as turning clockwise to lock push up on the back side locking bar and then remove, continue tuning cw to remove lock cylinder. Unbolt the large lock nut and washer on the cylinder case to remove from glove compartment itself. Assemble in reverse order.


How do you remove a lock cylinder from a 1972 Chevelle without the key?

you don't.


How do you replace the ignition switch on a 1994 Camaro?

disconnect battery. remove steering wheel. remove turn signal switch. remove the buzzer switch with nedle nose pliers. then place key in ignition and set to lock position. remove lock cylinder retaining screw. then pull cylinder straight out.disconnect passkey connector from bulkhead and remove retaining clip.use a wire to aid in installation of pulling harness through column.


How do you remove an ignition lock cylinder from a 1994 B 4000 Mazda truck?

(1)Remove the steering wheel, steering column cover and steering column shrouds; (2) turn the steering lock to the On position; (3)insert a 1/8" diameter wire, punch or small screwdriver into the lock cylinder housing and release the actuator pin while pulling on the cylinder. Installation is the reverse of the removal steps. - Mazda Pickups Repair Manual


How do you remove 2002 Honda CR-V door lock cylinder?

What holds the door lock cylinder into the handle on 2002 Honda CR-V