Auto Parts and Repairs
Chevy Silverado
Chevy S-10
Ford Expedition Eddie Bauer

How do you remove a manual window crank from the door panel in order to get to the speakers in the door on a 1997 Chevy S10 pickup?

313233

Top Answer
User Avatar
Wiki User
2011-09-13 06:14:19
2011-09-13 06:14:19

IF there isn't a cover that unsnaps over IT-then U need a special slotted tool that goes behind the crank & pushes the C clip off-IT slides in right behind the window crank-ITS just a thin piece of metal that's slotted 2 push the clip off .

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Remove the weather seal from around the rear window. Remove the window retainers. Gently tap on the window from the inside. The window will fall backwards. Reverse the process to install the new window.

User Avatar

to take out the rear speakers in a 1995 Chevy Beretta you need to remove the plastic molding on the inside of the passenger compartment in the backseat area of the car, and pull the backseat forward to get to that rear deck by the window. you will also need to remove the rear brake light in the window. when installing new speakers it is a good idea to cut the fabric so that you can get to the speakers much more easily if you need to remove them again.

User Avatar

First you need to remove the door panel.Then remove the door handle bracket.Peel back the moisture shield.Tape the window into place,then unbolt the window from the regulator.Remove the window regulator from the access hole in the door.

User Avatar

Manual window cranks are held on with a screw on 1997 Honda Civics. Remove the plastic cover on the handle to reveal the screw. Loosen and remove the handle. Replace with a new unit.

User Avatar

You will need to remove the inside door panel in your 1989 Ford Mustang. Remove the window retaining clips. The window will lift out. Reverse the process to install the new window.

User Avatar

you have to remove the back dash cover, remove the little connection that goest to your window as well. the speakers are accessed from the top.

User Avatar

remove door panel, roll down window 1/3, unbolt from track

User Avatar

To remove the window knob,you need to purchase a tool at any auto parts store, you would then slide the tool behind the window crank and simply push out the clip that holds the window lever in place.

User Avatar

how do you bypass electric window switch on 88 toyota pickup

User Avatar

Their is a special tool to remove manual crank window cranks and it will work for almost any car. You can pick one up at auto zone

User Avatar

replace 1987 dodge pickup/power window motor

User Avatar

The question you ask is too involved for a proper answer. You may want to go to a car parts store, or book store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.

User Avatar

1: Lay rear seats down. 2: Remove 4 push plugs in plastic trim. Remove trim. 3: Remove the trim from around the rear window. Both sides. Be carefull not to break wires or connectors for defrost. 4: Remove rear window pad. Speaker grills are attached to this. 5: Push the black tabs to raise speakers out. Tabs are on the left and right of speakers. 6: Disconnect the speaker wires. Not hard to do. DO NOT TRY TO REMOVE THE SPEAKER GRILLS WITH A SCREWDRIVER. They are part of the R/Window pad.

User Avatar

You have to remove the door trim on the inside of the door. Also remove the window crank handle if it is manual windows. 1. remove the window regulator by unbolting the regulator from the door shell and sliding the window guide arms out of the window channels. 2. You then remove either side or both sides of the vertical window channel that the window goes up and down on. 3. Finally, most of the time you need to remove the window rubber seal that runs horizontally along the bottom of the window opening to get the glass and the regulator channel that is attached to the glass out of the door.

User Avatar

There should be an Allen head screw in the middle of the connection.

User Avatar

there is a small clip between the handle and door panel that u have to remove it is easy if u have a small pick to hook it with then to install just place clip on handle and push on the window regulator shaft.

User Avatar

Remove the door panel, then remove the plastic sheeting. Then you can gai access to the window tracking. Remove the two 10mm nuts, that hold the window glass to the upper track. Remove the glass from the door, and install the new one in the reverse procedure.

User Avatar

To repair a stuck driver-side manual window, use a screwdriver to remove the screws attached to the door panel. Pull the door handle away from the door and lower the window regulator to the lowest possible position.

User Avatar

How do you remove the manual window cranThere should be an Allen type set-screw in the base of the handle. It will be recessed, and you'll have to turn the crank to access it more easily. Remove the setscrew, and the handle slips off of the stud. If the window is down, and it begins to rain, you can roll the window up by holding it onto the stud, and turning, or you can use a small pair of vise grips. Just try not to damage the teeth on the stud.

User Avatar

The doors you have to remove a bolt in the handle area (i believe its just under it) and then you have to remove the window crank (which requires a special GM tool), Then the door panel pops off revealing your speakers. Now the dash speakers they just have screws that hold the panel in. Once that panels off you just take the screws out and put your new ones in. MrNathanielJ.

User Avatar

you have to pull off all the inerior paneling in the truck to expose the framework. then pull it out. sometimes a heat gun is helpful to soften the sealant that they use when they put the window in.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.