Drain the water from your 1972 Chevy Corvette radiator. Remove the radiator hoses. Remove the stabilizing arm retaining bolt. Remove the radiator retaining bolts. Reverse the process to install the new radiator.
Drain the radiator into a container. Remove the upper radiator hose at the engine and remove the 2 bolts in the thermostat housing. Remove the thermostat and clean the surfaces. Install the new thermostat ,upper radiator hose and refill the radiator.
Drain the radiator down into a container and remove the top radiator hose from the engine. Remove the 2 bolts on the housing and remove it and the thermostat. Clean both surfaces and install the new thermostat.
i need a step by step instruction on how to remove or replace a radiator of a 2005 3.4L chevy impala
Remove the coolant from your 1997 Chevy Malibu radiator. Remove the bottom radiator hose. Run water through the top of the radiator allowing it to run out the bottom.
Remove the plug at the bottom or the rear of the radiator or remove the lower radiator hose
Partially drain the radiator into a container. Remove the upper hose at the engine end. Remove the 2 bolts that hold the thermostat housing and remove the thermostat. Clean both surfaces and install the thermostat, install the housing and the 2 retaining bolts. install the upper radiator hose and top off the coolant. It is located at the engine end of the top radiator hose in the thermostat housing.
Drain the radiator into a container. Remove the upper radiator hose at the engine end. there is 2 bolts in the housing that hold the thermostat. Remove them and the thermostat and clean both surfaces. Install the new thermostat and housing. Install the upper hose and top off the radiator with a 50/50 mixture of antifreeze and water.
Remove The Radiator And Have A Radiator Shop Test, And Flush It.
Partially drain the radiator down . Remove the upper radiator hose at the engine end. The housing is where the thermostat is located. Remove the two bolts and clean Both surfaces. Install the new thermostat.
Drain the vans radiator. Remove the top radiator hose and water inlet. take the thermostat out. Put in the new thermostat and re install the inlet and hose. Refill the radiator.
Drain the radiator down 1/2 way. At the engine end of the top radiator hose is the thermostat housing. Remove the housing and install a new thermostat.
Drain the radiator. Remove the fan and shroud if needed. unbolt the old pump and remove. Install the new pump, put all parts back, then refill the radiator with fresh coolant.
Drain the radiator. Remove the top radiator hose. Remove the water inlet, and take the thermostat from underneath it. Install the new thermostat. Reinstall the inlet and hose. Fill the system with coolant.
It is on the bottom of the radiator. Sometimes it is easier to remove the lower radiator hose.
To replace the thermostat on a 91 Cavalier you need to drain the radiator. Remove the top radiator hose and water inlet. Remove the thermostat from under the inlet. Install the new thermostat and reinstall the inlet and hose. Fill the radiator with fresh antifreeze.
There isn't one. You have to remove the lower radiator hose, which is a poor design.
with the correct tools
Remove the radiator and take it to a radiator shop.
1. Drain the cooling system.2. Remove the lower radiator hose from thermostat outlet.3. Remove the thermostat outlet bolts and outlet. Remove the thermostat.4. Clean the mating surfaces of the radiator outlet and the radiator outlet pipe.To install:1. Install the thermostat.2. Install the thermostat outlet and bolts.3. Install the coolant outlet attaching bolts and tighten the thermostat outlet bolts to 10 ft. lbs. (14 Nm).4. Install the lower radiator hose to thermostat outlet.5. Fill the cooling system.6. Inspect for leaks.
With engine cool, drain off aprox 2 qts of coolant from the radiator, remove upper radiator hose from thermostat housing, remove thermostat housing, remove thermostat and seal, reverse order to install, make sure thermostat spring is facing into the engine.
No, you can replace the grill without removing the radiator.
I am trying to drain old antifreeze and replace with new and cannot figure out how to remove the radiator plug on my 2001 Chevy impala 3400V6 engine?
Follow the upper radiator hose from the radiator to the engine. It will lead you to the thermostat housing. Drain coolant from radiator, remove upper radiator hose from engine, remove the two bolts holding the thermostat housing to engine, remove housing, remove thermostat.
The drivebelt routing decal on the radiator shroud to help during drivebelt install