0
http://customtacos.com/tech/index.php?page=index_v2&id=77&c=6
- follow steps 1-4 - once you get the black trim plate off, the stock radio is held in place by 4 nut/screws. - remove the nut/screws - pull the stock radio out - disconnect the harness - disconnect the antenna - disconnect any auxiliary input devices (i.e. CD changer) if you have them
- when you go to put your new deck in, just follow these steps in reverse
cheers!
Wiki User
∙ 12y ago
Wiki User
∙ 15y agoThe Blower - heat and vebt control unit under the radio is a one piece unit the is held inplace by locking arms thatonthe left and right side of the unit The can be loosened and the unit remover by carefully apply pressure to the top left than the top right sides After it is removed you can access the 4 sheet metal bolts that hold the radio in plkace and pull it out This is not hard to do - just be careful when removing the control unit also a special tool can be purcahsed at local auto parts stores used to remove side panels in doors - this can also be used to remove the control unit Here are some step by step instructions on removing and installing the stereo in your 2005 2006 2007 2008 2009 Toyota Tacoma: http://www.tacotunes.com/installation/tacomadash/
Wiki User
∙ 16y agoPop off the A/C Control knobs, then remove the screws. Then remove the a/c assembly, more screws, then it slides out.
Wiki User
∙ 11y agoHeres a write up on how to remove a radio in a tacoma 2005 -2013
http://freecarsupport.com/diy-write-ups/2012/9/17/how-remove-install-a-radio-in-a-2005-2013-toyota-tacoma
Wiki User
∙ 16y agoTAke off the panel that surrongs the stereo - then you'll see 4 bolts/screws holding the stereo once these are removed stereo slides out easily.
Wiki User
∙ 15y agoTake the screws out of the radio and pull it out!
Wiki User
∙ 12y agoThis question has been answered before on Answers.com. I have added a link to the answer below.
Wiki User
∙ 15y agohttp://home.doramail.com/toyotaecho/
Add your answer:
Earn +20 pts
Remove 1993 Toyota Camry factory radio?
Remove the 1993 Toyota decorative radio cover in. Remove the radio retaining screws. Pull the radio out. Remove the wiring harness.
What kind of fuse do you need for a blown out radio fuse in a Toyota Tacoma?
the same as what came out
How do I install Radio in Toyota Tacoma?
yes, if going with a single din radio, you will have to buy a kit to fill in the gap.
How do you remove face cover off 2001 Honda crv factory radio?
If you are referring to the factory supplied radio, it is not a 'component' type radio. It must be removed from the dash and dis-assembled.
How do you remove the factory radio to unplug the antenna and install satellite radio wire?
you can't do it yourself you have to get help from a pro
Remove 1993 Toyota Camry factory radio?
Remove the 1993 Toyota decorative radio cover in. Remove the radio retaining screws. Pull the radio out. Remove the wiring harness.
Where is the radio fuse for Toyota Tacoma?
The Toyota Tacoma radio fuse can be located in the fuse box. The fuse box is in the engine compartment. The location of the radio fuse will be listed on the inside cover of the fuse box.
What kind of fuse do you need for a blown out radio fuse in a Toyota Tacoma?
the same as what came out
How do I install Radio in Toyota Tacoma?
yes, if going with a single din radio, you will have to buy a kit to fill in the gap.
Where is the flasher on a 2006 Toyota Tacoma?
in the center of the car, right under the radio, next to the clock.
How to remove factory radio from 2004 ford f150?
How to remove the factory radio and disconnect wirring harnes in a 2004 f150 ford truck
How do you remove radio in 1995 Toyota Corolla?
To remove the radio in a 1995 Toyota Corolla, first pry the radio frame from the dashboard using a flat tool like a screwdriver. Then, press in on the pins at each side of the radio and slide it out of the dashboard. Remove the wires from the back of the radio.
How do you take the factory radio out of a 1990 Chevy Caprice?
Begin by removing the decorative cover from your 1990 Chevy Caprice factory radio. Remove the radio retaining screws. Remove the wiring harness and the antenna cable from the back of the radio.
How do you remove a factory radio in a 2005 Chevy Malibu?
Remove the retaining cover to your 2005 Chevy Malibu radio. Remove the radio retaining screws. Slide the radio out. Remove the wiring harness and the antenna cable.
How do you remove the factory radio from your 1996 cadillac deville?
you eat it
How do you remove a radio on a 2000 Toyota Tacoma?
You need to remove the two screws above the climate controls. Then you pull the bezel around the radio off the dashboard. Next, you unscrew the four screws holding the deck to the dashboard and pull out the stereo and twist it so you can see the backside. Finally, you unplug and pull out all of the wiring.
How do you remove the radio in a 1999 Toyota pickup?
Around $100
