Auto Parts and Repairs
Chevy Lumina
Chevy Blazer S-10
DIY Projects

How do you remove the window crank on the passenger side of a 1994 Lumina APV?

151617

Top Answer
User Avatar
Wiki User
2012-05-25 17:04:30
2012-05-25 17:04:30

you can go to any auto parts store and buy a clip removal tool to remove handle. this tool will remove the c clip so you can remove handle. heres another way, but it takes longer. put a clean rag between door and back of handie, move the rag back and forth. when the rag makes contact with the clip, it should pop it off or far enough to remove handle. to put handle back on door. push the clip on the handle and push handle back on door good-day !

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Remove the inside door panel of your 1997 Chevy Lumina. Remove the linkage to the window crank. Remove the window crank retaining bolts. Reverse the process to install the new window crank.

User Avatar

If it's a true z34 90-94 there is no window crank they ALL had power windows.....

User Avatar

You will need to remove the inside door panel of your 1977 Chevrolet blazer. Remove the window crank linkage. Remove the window crank retaining bolts. Reverse the process to install the new window crank.

User Avatar

Remove the inside door panel. Remove the Allen screw from the window crank linkage. The window crank handles should come off.

User Avatar

There is a retaining ring behind the window crank. The easiest way to remove and install this is to buy the tool to remove the ring. You can use two small flat screwdrivers to push the flat ends of the ring down at the same time. Then you can just pull the handel off.

User Avatar

Pry the screwdriver between the door panel and the window crank base. Remove the metal clip slowly and carefully. Pull the base of crank to remove it.

User Avatar

How to Remove or Install Car Window Crank Handles check related link below

User Avatar

You need to remove the window hand crank with a window hand crank removal tool.

User Avatar

To replace the window crank handle on the 1993 Geo Prism, first remove the interior door panel. Then, access the screw that holds the window crank in place and remove it. You can then remove the handle itself.

User Avatar

Pull out the U-clip located on the base of the window crank.

User Avatar

you need a special tool to release a clip behind the handle any body shop guy could help ya out.

User Avatar

you can buy a window crank removal tool at an autoparts store that pulls the little pin off to remove it.

User Avatar

To remove the window crank on the 1992 Toyota Paseo, first pry off the interior door panel. Then, access the screw that holds the crank in place. Remove the screw and the handle will come loose.

User Avatar

Remove inside door handle and window crank handle, remove inside door panel, remove vent window and channel assembly, remove window.

User Avatar

You can remove the window crank handle by just using a simple shop rag. How you do this you slide the rag(unfolded) between the door panel and window crank and rotate around the window crank until you snag the clip that is retain the window crank. The clip is a simple wire clip shaped like a "C" To reinstall you place the clip back in the groove on window crank and press back on the window regualtor shaft

User Avatar

I want to take off the pulley wheel off,from a 1992 chevy lumina apv van.

User Avatar

Their is a special tool to remove manual crank window cranks and it will work for almost any car. You can pick one up at auto zone

User Avatar

push in on the door pannel by the crank and remove the snap ring behind the pivit point

User Avatar

All you need is a paint can opener. Under the window crank there is a horseshoe shaped pin and you just need to snag it and pull it out. Put down the window first and do the above. Then after romoving all the screws in the door panel lift up on it until it pops off.

User Avatar

You have to remove the inside panel, where the window crank is, or would be.

User Avatar

My 1990 Lumina 3.1 had the same problem and it was caused by the crank sensor.

User Avatar

My 1990 Lumina 3.1 had the same problem and it was caused by the crank sensor.

User Avatar

Your local auto parts store can sell you a very inexpensive tool to remove the clip that holds in the window crank handle. It should be under $10.

User Avatar

There is a clip holding the handle. It is located in the center in the back of the handle. There is a tool to remove & install it; but you can use a flat screwdriver carefully. Good luck.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.