I JUST DID THEM LAST WEEK ON A 1991 CAMARO. TAKE OFF THE INSIDE PLASTIC PANEL BY THE HOOD PULLER . JACK UP THE FRONT OF THE CAR, PLACE JACK STANDS UNDER IT. REMOVE THE FRONT TIRES. REMOVE THE PLASTIC FENDER DIRT SHEILDS. MAKE SURE YOU USE THAT JACK TO SUPPORT UNDER NEATH THE DOOR, I USED A SMALL 4X4 BLOCK BETWEEN THE JACK AND THE DOORS BOTTOM TO NOT DAMAGE THE DOOR. REMOVE THE TWO BOLTS FROM INSIDE THE PLASTIC PANEL YOU REMOVED. NOW REMOVE THE 3RD BOLT FROM THE OUTSIDE OF THE HINGE BY USING A RATCHET FROM INSIDE THE PLASTIC FENDER SHIELD AREA. USE PLIERS AND SQUEEZE THE PINS TABS IN WARDS. PULL UP AND IT SHOULD POP UP AND OUT. THE SPRING WILL ALSO FALL DOWN. PLACE THE NEW BUSHINGS IN PLACE, THEN INSERT THE NEW PIN. PUT THE BOLT FROM INSIDE THE FENDER AREA BACK 1ST. THEN THE OTHER TWO . DO NOT TIGHTEN TILL ALL THREE ARE HALF WAY STARTED. NOW TIGHTEN ALL THREE. PLACE THE PALSTIC PANELS BACK ON. SHOOT THE HINGES WITH WHITE LITHIUM GREASE. NEW PINS ARE LESS THAN 4 BUCKS EACH AT THE DEALER, BUSHINGS ARE UNDER A BUCK EACH. ALMOST ALWAYS IN STOCK. MY 1ST TIME DOING IT AND TOOK ME ONE HOUR PER DOOR.
by using only the information given, your answer is to replace the lower door hinge pin and bushing.
The '90 camaro has three bolts that hold the door hinge to the body and I believe three that hold the hinge to the door. The easiest way I've found is to score the position of the original hinge location and remove the bolts with the appropriate wrench with the door open. Be sure to have the door supported because it will try to sag. Once the new hinge is in place, align it to the original hinges location and tighten your bolts down.
need to replace door hinge pin on 189 mitsibushi Triton tray back
You can replace the top door hinge with bottom hinges on the 1992 as long as the hinge is for the cab doors. The hinges for the tailgate would not work on the doors.
jack the door up on the end of it and unbolt the hinge and replace with the new one.
you might need to replace the hinge pins.. or the complete hinge
You have to replace the whole hinge assembly, they don't make a hinge pin kit for the Thunderbird.
To fix a car door that is sprung due to a bent or damaged hinge, the best thing to do is replace the hinge. If the hinge is welded and not bolted to the vehicle, the entire door will have to be replaced.
To replace the door hinge pins on a 1997 Jimmy you will need to open the door up. Place two jack stands on the front and back of the door's length at the bottom portion of the door for support. Remove the damaged hinge pin with the proper socket. Place the new hinge pin in place and secure it.
need to replace door hindge pins and bushing,how do we get door off safely.
door hinges attached to door and hinge post
I wouldn't mess with the pin, the door hinge can have a washer/spacer placed under it and bring the door back in alighnment. I have new hinge pins available if you really want to change them.
My advice based on experience is to replace the entire hinge assembly.
Have to remove the door, then remove pins and bushings
there is no release you just push on the door near the hinge and it opens
You can't. Have to replace the hinge.
Replace the hinge pins and bushings.
Most problems with an automobile door hinge is worn out bushings. There is a small rubber bushing behind the adjustment bolts. Replace the bushings.
Your local auto parts store can sell you an inexpensive tool to remove and replace that door detente spring. Other hinge parts such as the pin and roller for the door detente and hinge pins and bushings are also available.
you take it to a shop
Pull the inside door panels off and you will see there bolted in the door.
Pull the inner door panels off and the speakers are mounted in the door.
I have a 1999 gmc 1500 sierra,need to replace door pins and bushings.door sagging.
This link is titled "door hinge", but actually pertains to the catch-strap: http://volvospeed.com/vs_forum/index.php/topic/79630-how-to-repair-a-clunking-grinding-broken-door-hinge/