YOU HAVE TO REMOVE THE GLOVE BOX. ITS MOUNTED ON THE FRESH AIR DUCT.
How do you replace a fan blower resistor on a vauxal Corsa?
The blower motor speed resistor is burned out. You can replace only the resistor but the resistor probably burned out because the blower motor is going bad. If you want to fix it for good, replace both the blower motor and blower motor speed resistor.
resistor is located right by the blower motor itself ..Follow the electrical wires. It will look like a flat chip board from a cell phone!
how to replace blower resister on a 325i BMW 2002
# Locate the blower resistor under the right-side of the instrument panel # Disconnect the electrical connector from the blower motor resistor # Remove the blower motor resistor mounting screws and remove the resistor from the housing # Installation is the reverse of removal
Check to see if you are getting power to blower motor - if so replace blower motor If not check fuse, switch, resistor pack.
A blower resistor can be replaced, in your 2002 Oldsmobile, by removing the resistor wiring. Remove the retaining screws. Reverse the process to install the new resistor.
have you checked the fuse if so then you will need to replace the resistor for the blower hig and low dettings have you checked the fuse do you have 12 volts to blower if so then you will need to replace the resistor for the blower replace the blower motor
where is the switch resistor on 2003 buick
You must remove the glove compartment door to access the blower motor. On top of the blower motor will be wires connecting to the top. Release the connecter and let it dangle. Then using a screwdriver, remove the blower resistor on top, where the wires connected, and replace with a new resistor.
To replace a blower motor on the resistor first you take off the nozzle and then you go into the motor through the nozzle and unlock it then repeat and oil and done.
One can replace blower motor resistor on 2003 Nissan altima by removing the old using spanners and replacing it with a new one.
To change the blower motor resistor in a 2002 Nissan Maxima, locate the blower motor resistor under the glove compartment on the passenger side of the vehicle. There is a clip that is depressed and then the resistor will slide out. Remove both ends of the resistor and then replace with the new resistor.
Check to see if you have 12 volts at the blower motor. If yes then the blower motor is bad. If no, then the resistor, relay, or fuse is bad.
To test the blower motor resistor, unplug the resistor connector. Each blower motor switch input terminal on the resistor must have continuity to the resistor output terminal, which is connected to the circuit going to the blower motor. If the blower motor resistor continuity does not check OK, replace the faulty resistor.You need a multimeter to test the resistor block and there should be continuity between all terminals.
You'll find the heater blower motor resistor in the heater/air conditioner compartment. This compartment is location underneath the dashboard. This is the part that allows the heater blower motor to change the fan's speed.
you need a new blower motor resistor with auto temp control
The blower resistor is located under the dash, near the floor, on the passenger side of the vehicle. I had to replace the resistor about a year ago. It is not an easy place to work in. You have to remove the blower unit in order to get at the resistor. Not fun, but rewarding when you actually do it yourself.
how to replace heater fan resistor on Nissan Sentra 2003
this resistor is located next to the blower motor in the heater plenum. the coils sit in the air stream. remove the connector and the fasteners and pull the resistor block out.
You will need to change the blower motor resistor by finding it near the air duct system. You will take the old resistor off and replace it the same way.
Something called a blower control module takes the place and is found in the hole where you would find a blower resistor, so there isn't a blower resistor in that vehicle. As far as the blower control module is concerned, the module is serviced as a unit. No part can be fixed or replaced. This is not to be confused with the control head in the dash. The blower control module is held into the heater box with two 8mm screws outside the firewall under the hood, where you would normally find the blower resistor pack.
the heater blower resistor is located on the passenger side footwell near the firewall. a complete how-to replace the resistor, along with photos is available on newcougar.org http://www.newcougar.org/forums/how-tos/3732-fixing-heater-blower-resistor-install-photos.html