Turn your ignition switch to 'ON' (don't start the car) The reset button is on the driver's side instrument panel, this is also where your fuses are located. Press the recent button once and your 'Change Oil' light should start to flash. Press the reset button again and your 'Low Tire Pressure Light should start to flash. Press and hold the reset button until you hear a few chimes and then let go.(wait tell the light shuts off then let go) Your light should then be off.
To get to the fuse box, you must have the drivers door open. Pull on the plastic piece and the reset button is there.
Just press the reset button at the fuse panel on the driver side. Press it for some seconds and it will clear the light.
My tire pressure light has been on forever. I finally got it to go off by holding in the reset button til it blinked and then shut off. You can try that.. if not it's just gonna stay on.
Open up the drivers side door and you will see a cover pannel on the dash side. Pull the open and press the reset light until the light flashes. You must have the car ON.
turn off engine, and start again
Have vehicle scanned to determine the problem
how do you reset change the oil light in a 2004 alero?
Turn the ignition key on for 10 minutes and it will reset.
get a code scanner, or borrow one from a parts store, plug it in and clear codes
GM vehicles do not use inertia/reset buttons
There isn't one. Ford is mainly the only ones who have a reset switch.
I have a 2002 alero how do you reset, the coolant light is always on. Thanks, Alero owner
When your security light comes on and your car will not start, turn you key to the on position and wait 10 minutes. The light will go off and you need to turn the key to the off position, then restart your car.
on the drivers side there is a fuse panel on the dash. there you need to press the reset button once and then your change oil light will blink. then you want to press it again and the low tire pressure light will blink hold the reset button until it beeps and then let go and then press the reset button again and the light should disappear. Hope this helps!
you can't really reset a battery.... to reset the sensors and the panel, open the fuse panel by the drivers door and hold the red reset button for about 10 15 seconds. It should make the same ding sound as when an indicator light comes on
Should reset itself when fluid is added unless sensor is bad
Have the problem repaired and they will reset the light. If you DIY then disconnect the negative battery cable for 5 minutes. If that does not reset the light you will have to have it reset with an OBD2 scan tool.
turn switch to on position (all the dash lights on but engine off) wait for all lights to go out then press accelerator pedal three times
when you open the drivers side door you need to remove a panel door that will allow you to access the fuse box locate the the red button to the left side and press it a couple of times until you see your tire light flash after it starts to flash hold it in for a couple of seconds and you will hear a chime 4 times and you light will be reset you need to have your key turned on but not running to be able to do this.
How to reset the tire pressure light on a 2007 Nissan Sentra?
General Motors products do not use inertia/reset switches
If you open the driver door, on the side of the dash you should see a small removable plastic plate. Pull it off with your finger and inside is a small red reset button, somewhat in the middle. Push it once the oil light should flash, push it again the tire pressure light will flash. Push and hold and it will reset! :) Hope this helps!
open fuse box on the driver's side (just pull the door off the fuse box) find the red button that says "reset" press it, the Check Oil light should come on. press it again. the Check Tire Pressure light should come on. now, press and hold the reset button. the tire pressure is now reset and you can put the fuse box door back on. for best results, drive normally at various speeds to "re-teach" the tire pressure monitor the correct tire pressure.
hi how do i reset tire pressure sensor light on
It does not have a reset. If the oil light is on, the sensor has failed or the oil pressure is too low.It does not have a reset. If the oil light is on, the sensor has failed or the oil pressure is too low.
there are two things to do first you can reset the computer by disconnecting the battery for about 1/2 hour then if your light still comes on after that just go to an autozone and they will check the light out for you for free and let you know what needs to be fixed and what code you have.