0
How do you tell if you have a bad clutch master cylinder or slave cylinder on a 93 F150?
Wiki User
∙ 16y ago
The clutch will not depress after you have pushed it in to shift gears. It may come back out a few times but this will be the beginning of the problem. I just changed mine recently (at a Ford dealer) as this was the problem. Not a cheap job to get done by any means. Have the mechanics check your clutch and pressure plate for wear as this would be the time to get it all done. The job cost approximately $1300.00 bucks (candian funds) and will be about half that price if you just change the slave cylinder. It shifts like a new truck now!!!
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
Where is the master cylinder for the clutch in a 1983 ford F150?
The clutch master cylinder is under the hood, drivers side, on the firewall. It is between the brake master cylinder and the drivers side fender. The cylinder is very small in comparison to the brake master cylinder. It goes through the firewall and connects to the clutch linkage under the dash.
How do you bleed the clutch slave cylinder on 2000 f150?
Best answer I've found is here (I have a 2001 F150): http://www.clutchwizard.com/fordtruck.htm Basically the problem is that the master cylinder is at the wrong angle to bleed the system completely with the master cylinder attached to the firewall. You have to take the master cylinder off the firewall and detach it from the clutch pedal, then tilt it to get the air into the line. After that, you bleed it in more or less the usual way, with a helper operating the bleed valve, but pushing the piston directly instead of pushing the clutch pedal. The alternative is to assemble the whole system off the truck and bleed it on a bench. Good thing they made the master cylinder and the brake cylinder out of PLASTIC, and put the slave cylinder INSIDE the bell housing, huh? (My slave cylinder went at less than 60K).
Do you have to remove the slave cylinder from a 2004 f150 by removing the tansmision?
Yes , the slave cylinder for a HYDRAULIC clutch is inside the manual transmission bellhousing. It slides over the transmission input shaft and is bolted to the transmission
How do you bleed the clutch on an 86 f150?
Not positive on yours but usually it's like this. Make sure the clutch master cylinder reservoir is full. Then have someone push and hold the clutch pedal to the floor. Open the bleeder valve on the clutch slave cylinder, letting the fluid squirt out, close the bleeder valve. Repeat process. You do this until the clutch fluid comes out clear with no bubbles. Usually 2 or 3 pumps will do it. Then make sure the bleeder valve is closed tight, top off the clutch master cylinder fluid resovoir and you're done. Hope this helps.
How do you bleed the hydraulic clutch on a 1991 Ford F150?
this is a 2 man job period, top up the master cylinder and pump your petal as you would doing a brake bleed job, there will be a master slave cylinder on the transmission with a nipple on it (I don't know the actual size but I believe its 5/16" or so) it will look and feel like a grease nipple, just crack that open and shut it when the petal hits the floor, repeat as nesscary, don't forget to keep toping the clutch master cylinder The slave clyinder on my 1991 F 150 does not have a bleeder nipple !
Why doesn't my 2001 ford F150 not go into gear?
If it is a stick, it could most likely be the clutch master cylinder or the slave cyliner. Check around the master for any leaks. Also, check the transmission itself and the clutch pedal in the cab. If there is fluid on them, that is probably your problem. Another thing could be the clutch pressure plate. If it is an automatic, check the transmission fluid and consider a transmission service.
Is slave cylinder on 2000 f150 4.2 inside transmission?
Yes , the slave cylinder for your hydraulic clutch is inside the manual transmission bell housing. It slides over the input shaft to the transmission and is bolted in place inside the transmission . To CHANGE the slave cylinder the transmission has to be removed , but the lines to the slave cylinder CAN BE BLEAD from a fitting that extends outside of the transmission bellhousing
Why does your clutch pedal stick down on a 1996 F150?
Bad or improperly installed throw out bearing? broken throw out bearing fork? hydraulic? bad slave cylinder?
Where is the clutch master cylinder reservoir located on a 1995 Ford F150?
It is on the firewall, drivers side, next to the vacuum brake booster. It is the small reservoir closest to the fender.
How do you replace the slave cylinder in a 1988 ford F150 6 cylinder fwd?
you just replace it
Where is the bleeder screw for a 1996 Ford F150?
Bleeder screw for clutch is at the slave cylinder, on the bell housing of the Transmission. The bleeder for the brakes is on the calipers, and on the backing plate of the rear drum brakes
Where can one purchase a master cylinder for a Ford F-150?
A Ford dealership would be the best place to find a master cylinder for a Ford F150. Parts Geek, Parts Train, and eBay also have master cylinders for a Ford F150 for sale.
