0
How due you remove the water pump pulley from a 1997 Chevy venture the pulley turns every time you try to undo the bolts?
Wiki User
∙ 16y ago
put the belt back on and hold the pully with your hand while losing the bolts with a wrinch
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do you put on a water pump pulley for the serpentine belt on a 1995 Chevy Lumina minivan?
there should be 3 or 4 bolts that hold pulley on, just remove these bolts a pulley should come off. but remove belt first ! if pulley keeps turning while removing bolts. you can hold it stationary with a scredriver or similar.
How do you pull a damper pulley from a Chevy 350?
If you are just removing the pulley, Then just remove the bolts that hold it on being sure to remove the bolt that is in the middle of the pulley too. Then take a hammer and knock it off.
How do you replace a condenser for a Chevy Venture?
remove the radiator by removing the two support bolts up top it may have a plastic cover over these bolts discharge the a/c system remove the bolts holding the a/c lines on and remove the condenser
How do you replace water pump for 2002 Chevy Venture?
Easy one.Warm engine to full operating temperature.Loosen, slightly 4 bolts from water pump pulley (smooth at the top, towards the fron of the car).Remove serpentine belt.Remove 4 pulley bolts.Drain radiator.Remove 5 water pump bolts and thoroughly clean any old gasket.Reverse procedure to install.
How do you remove power steer in pump on factory no air Chevy?
You have to remove the pulley first and you need a power steering pulley puller to do it. You can get one from Napa for usually about $40. There are bolts behind the pulley that hold the pump to the mounting bracket.
How do you remove a power steering pump on 1990 Chevy Cheyenne 4.3?
open hood insert tool use tool remove pulley remove bolts remove pump
How do you remove the power steering pump on a 1994 Chevy Corsica?
Loosen, then remove the belt. Shine a light through one of the holes in the PS pulley and turn it slowly. You will see three bolts through the holes. Use a 13mm socket and a swivel to unscrew and remove these bolts. Lift the pump out of position and remove the hoses. Use a Power Steering Pulley Puller to remove the pulley. This puller grips the pulley by its center hub. Any other type of puller will destroy the pulley and then you will need a new pulley.
How do you remove seats in Chevy Venture?
Locate the bolts at the base of the seats and unbolt them. You'll have to disconnect any electrical connections if you have power seats.
How go you change a water pump on 1998 Chevy Venture?
Here is the procedure to do the job. 1 - Drain the cooling system until the coolant is below the level of the water pump. 2 - Remove the guard for the drive belt. 3 - Loosen the bolts for the water pump pulley (do not remove them yet). 4 - Remove the drive belt. 5 - Remove the bolts for the water pump pulley. 6 - Remove the water pump pulley. 7 - Remove the bolts for the water pump. 8 - Remove the water pump. 9 - Remove the water pump gasket. 10 - Clean the water pump mating surfaces. Reverse the procedure to install the new pump, making sure you use a new gasket. Refill the cooling system & check for leaks.
How do i take my ac out when i cant get to bolts out when the pulley is in the way of the bolts?
use a thin wrench or if possible just remove the pulley
How do you change the power steering pump on a 96 Chevy suburban with a 57l vortec?
need a puller to remove the power steering pump pulley, then remove the bolts holding the pump on
How do you repair a crankshaft pulley for a 98 Saturn SC2 DOHC?
u need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removalAnsweru need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removal Answeru need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removal
