Chevy Impala
Jeep Cherokee Sport
Ford Expedition XLT
Late Model 1979-New Ford Mustangs
How To

How to Remove door panel 98 jeep?

808182

Top Answer
User Avatar
Wiki User
Answered
2007-03-14 17:46:48
2007-03-14 17:46:48

The process is a little different depending on whether you are doing the front or rear doors. For the front, remove one screw on the top side of the panel closest to the outside mirror. Remove a second screw behind the door pull latch. There are three more at the pull handle and arm rest. Then the trim panel must be pryed away from the door using a pry tool. There are 10 fasteners. You can pull the trim away from the door a small bit and run your fingers behind the trim to find them. Start from the bottom and run up the sides. Once loosened, lift the trim up then out to release. You then have to disconnect the handle and lock latch rods (plastic clips), and then the wire harness connectors. The panel is now off. The rear doors are similar, just with less screws and fasteners. Be careful not to damage the ten fasteners.

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


remove door panel then remove screws behind mirror. remove door panel then remove screws behind mirror.



You will need to remove the inside door panel, by prying outward on the door panel retaining clips. When the door panel is removed the door handle assembly will be visible. Remove the door handle retaining bolts.


The 1998 Chevrolet Blazer door panel is held in place by eight retaining clips. Pry outward on each retaining clip to remove the door panel.


remove door panel. disconect electrical connections and unbolt the mirror using a 10mm socket


The 1998 Honda Civic drivers side door panel is held on by eight retaining clips. Pry outward on each retaining clip to remove the door panel.


Open the drivers door, remove panel on left side of dash. This panel is covered when the door in closed.


Door Panels Removal & Installation 1. Remove the sail panel (Front Doors Only). 2. Remove the door panel by carefully lifting the panel upward to release the retaining clips. 3. Remove the electrical plugs that control the windows, exc.The installation is the reverse of the removal.


* Disconnect the negative battery cable * At the bottomof the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors


open the driver side door. There is a panel on the dashboard that is really easy to remove when the door is open... ope panel, see fuses and on the panel is a diagram to locate which is which!


same as 98 and others answered elsewhere in this forum. http://neons.org/howtos/door/


Go to this website. It will show how to remove the door panel and the side mirror.


depending on model the 94-98-99 old body you have to release late assembly on the side and the remove panel to then remove both screws that hold it to the door and pull out. on the 00 up you can just remove panel and remove screws that hold it to the door.


Door Panels Removal & Installation 1. Remove the sail panel (Front Doors Only). 2. Remove the door panel by carefully lifting the panel upward to release the retaining clips. 3. Remove the electrical plugs that control the windows, exc. 4. Repair handleThe installation is the reverse of the removal.


http://www.bodyshopzone.com/archives/trim/door_panels/GMC/Jimmy_1999/front_.html



Remove the Door Panels and remove screws holding the speakers. Door Panels Removal & Installation 1. Remove the sail panel (Front Doors Only). (Triangle looking shape near the side view mirror) 2. Remove the door panel by carefully lifting the panel upward to release the retaining clips. 3. Remove the electrical plugs that control the windows, exc.The installation is the reverse of the removal.


See "Related Questions" below for details on removing the door panel to get at the speakers


There are 2 screws in the bottom of the door and 2 more under the door handle in the inside of the car just pop it off at the seems and screws will be inside pop panel off and unplug the power locks


this is actually the easiest thing to do. DO NOT pry it off. under neath the door panel there shold be 2 screws remove those. Then where the inside door handle is there is a thing you pop off and there is a screw under neath there. After you remove that screw, remove that piece from the door handle, so you can see the inside of the door. Then just lift up from the bottom of the door and it pops right off.


* On models with power door locks and/or power windows disconnect the negative battery cable.If equipped with Delco Loc 2 or Theftlock audio system make sure you have the activation code * On models with power door locks pry the power door lock switch out of the door trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with power windows pry the power window switch out of the trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with manually-operated windows remove the window regulator handle * Remove the trim panel screws * Once all of the screws are removed detach the trim panel from the door disconnect any electrical connectors and remove the trim panel from the vehicle by lifting it up and away from the door


On the newer models (1991 +) they are located in the door lock mechanism in the door. The door panel needs to be removed to get to them.


On the 98 Grand Cherokee you have to remove 4 screws I believe. 3 are easy to spot they maybe coverd with round plastic caps to match the interior of the Jeep. Just pop offthe caps with a screwdriver and you will expose the screw. The last one is inside the door release (handle), if you look behind the handle you will see the out line of a small square panel. Remove the panel and you will find another screw. Then slowly pull the interior panel off. There are still some plastic pegs holding the panel to the door put they will pop off. Next need to disconnect the wires from the back. Then the panel will be free and in your hand. Next you need to peel back the plastic layers to expose the inside of the door. I have not had the pleasure of the window motor, so can't help you there. pls see... http://www.faqfarm.com/Q/What_is_wrong_when_the_front_passenger_power_window_motor_sounds_like_it%27s_going_to_work_but_then_stops_and_the_window_will_not_move_on_a_1999_Jeep_Grand_Cherokee


Door Panels Removal & Installation 1. Remove the sail panel (Front Doors Only). 2. Remove the door panel by carefully lifting the panel upward to release the retaining clips. 3. Remove the electrical plugs that control the windows, exc. Clean out the debris.The installation is the reverse of the removal.Same goes for the sunroof open and clean out the debris.


Remove the door panel. Towards the front of the door there are two screws holding the mirror on. Inside the door are two connectors that connect the mirror wires to the door. I have a 98 and if it is the same process that's all you need to do.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.