0
The price to replace these items can be anywhere from 20 dollars to 450 dollars. It depends on where you go to have it done and what they charge.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
How do you replace hinge pins on 2003 avalanche?
need to replace door hindge pins and bushing,how do we get door off safely.
How do you replace a hinge pin on a 1987 Chevy blazer?
break off the bottom bushing that hold door pin pick up on the door slightly use a hammer and screw driver to drive pin out and replace
How do you replace a door hinge on a 2002 Chevy S-10?
BIG JOB! The original hinges are welded in. They do sell pin and bushing kits to restore the original hinges, much easier to do than replacing the whole hinge.
How do you adjust the door on 2002 Chevy s-10?
Replace the worn door hinge pins and bushings and the door should line up where it belongs. The pin and bushing kits are available from your local auto parts store.
How do you repair door hinge on 2001 Sunfire?
Most problems with an automobile door hinge is worn out bushings. There is a small rubber bushing behind the adjustment bolts. Replace the bushings.
How do you adjust the front fender on an 1981 camaro it is rubbing on the door?
by using only the information given, your answer is to replace the lower door hinge pin and bushing.
How do you align 2004 Chevy Blazer door?
Replace the hinge pins and bushings.
Is their a oversize bushing kit for 2003 S-10 door hinge. already have a bushing kit in it. holes on door hinge ova-led?
I remove the door, weld up the holes and redrill them to the correct size.
How do you replace door hinge pin and bushing on Crown Victoria?
The pin will probably have to have the bottom end that is flared out cut off or drilled out. The pin can then be tapped out. This is easier if the hinge has been removed but then the door will have to be blocked up into place while the hinge is off.
How do you replace rear drivers side door hinge on Chevy aveo?
I need passenger door hinges for my chevy aveo 2007
How do you replace upper door hinge on 1996 Chevy blazer?
This is the most difficult hinge to replace on that vehicle. The original hinge is welded in place. The replacement hinge bolts in. In order to gain access to the back side of the hinge that is welded to the cab the entire dash assembly needs to be removed. Many times the original hinge can be rebuilt in place with pin and bushing kits and a little welding and drilling of the holes if they are damaged/oblonged. You will need a special tool to r&r the door hinge spring. This tool is available from your local auto parts store for less than $20.
1999 suburban my driver door hinge pin bushings have different od between the the top and bottom hinge no part stores show this in there books?
There are two different sizes of bushings for each hinge. On the Top door hinge the bushing go on the body side. The smaller of the two goes on the top hinge with the shoulder of the bushing on the top side of the hinge. The Larger bushing goes on the bottom of the hinge with the shoulder of the bushing on the bottom of the hinge. On the lower hinge the bushing go on the door side of the the hinge. The larger of the bushings go on the upper side of the hinge and the smaller bushing goes on the lower side of the hinge. When you put the pins in, the pin will go from bottom to top on the upper hinge and from top to bottom on the lower hinge. The pins will need to be tapped into place with a hammer. Be careful to not break the shoulder of the bushing. There is a tool that makes reinstalling the door spring a snap. It will probably cost $40, but it will save your knuckles and a lot of time. There are a couple of companies that make repair kits for these. On is from Dorman and the other is from HELP! The kits come with a small bushing, a large bushing, a pin, and a pin retainer. The retainers will look different depending on the company. Some look just like a thin washer and other look like an E-clip. If you go to an automotive parts house and ask for bushing and pin kits for you specific outfit they should know what you are talking about.
