0
Magnet or a good magnetic screwdriver, you would be suprised what all will work.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you remove lifters from a 1969 302 V8 Mustang Coupe?
Best way for me is to use a magnetic pick up tool and go in from the top after you have removed the rocker arms and push rods
What is the best program to remove a virus?
Optimo AV is the best antivirus software tool to remove the virus.
How do you change lifters in 1998 eclipse?
In order to change the lifters you must remove the Valve cover. I believe it is held down with 10mm bolts. After you remove the Valve Cover you till see the lifters. There are 16 of them. 8 close to you the 8 closer to the wind shield. I highly recommend you use a pair of clamps to hold your timing belt to the wheel because you can potentially knock your timing out of whack. After you have removed the valve cover gasket and have secured your timing belt you will need a small crowbar or some type of tool for leverage and a 10mm or 12mm socket to remove the braces over the rocker arms, rocker arms are what set on top of the lifters. There will be 2 bolts holding each brace on. Start from the left and work to the right ( if facing the engine ). After you remove the brace use your pry tool and pull the rocker arm off of the lifters. After you have the lifters will pull right up. Drop your new one in and replace the rocker arm and the brace. Go down the line doing so. Be careful as you get close to the timing belt wheel. For much more details and any information regarding the 1st & 2nd gen eclipse visit www.vfaq.com they have a complete how to on the lifters. Good luck
What are some causes of a ticking sound in a 1984 corvette engine?
the lifters may need adjusting or replacing. your engine not getting enough oil causes the lifters to make noise. not sure what motor you have in it but if it's an engine where you can tighten the lifters then you can buy a tool for it if you know what your doing
How do you replace the lifters on your 2001 Chevy Malibu LS?
remove valve covers, remove rocker arms,then pull up push rods.keep the rods in order, dont mix them up. i put them through a box or something to keep them ok!! lifters are on bottom of push rods. if you do not have a push rod tool! use a good magnet to get them out!!they ride against cam..the magnet should pull them out of the rod holes in engine.
How do you get the lifters out of a ford 3.0?
If it's an overhead valve engine that has the cam under the intake and not in the heads then you need to remove the intake manifold and the valve covers. Then remove the rocker arms and push rods. Use a valve lifter removal tool to make this job easier. The parts stores like Autozone usually have a loaner you can use for that. I do recommend using a Rust/Varnish remover type spray to soak down the lifter bores BEFORE attempting to remove the lifters to make it much easier. Good Luck!
How do you remove the factory radio in a 2003 Ford Crown Victoria?
there should be two holes, vertically, on each side of the radio, you can make a tool out of a coat hanger to stick into each side, when you have placed your homemade radio tool into the holes, simultaneously, you should be able to pull the factory radio out
How do you remove timing gear on 94 dodge 2.5?
There is a special tool ( a puller ) to remove the crankshaft sprocket.There is a special tool ( a puller ) to remove the crankshaft sprocket.
How do you remove the Harmonic Balancer on a 1994 Ford Tempo GL?
Works best with a air impact tool. There is room.
What tool to remove a front brake pads on a 2007?
= What tool to remove a front brake pads on a 2007? =
Which place provides the best staple remover tool in India?
The tool used to remove staple pins is known as the best staple removal tool. It is most frequently used in offices and is regarded as a student's best friend. It comes in a variety of forms and sizes and is highly fashionable and comfortable to use. Miles provide the best staple remover tool in India. It is super handy and comes in a budget.
How do you remove a broken headphone plug from an audio jack?
The best tool - would be a pair of small tweezers. That would probably help you remove the piece stuck in the socket.
