For a 1995 Ford Taurus 3.0 (except SHO), the torque specs are: 1st: 59 ft lbs 2nd: Loosen all bolts one full turn 3rd: 37 ft lbs 4th: 68 ft lbs The tightening sequence is: 6 - 4 - 2 - 8 5 - 1 - 3 - 7
There is no torque sequence just torque rocker arm studs to the proper torque
what is the engine torque spec for 1.6 opel monza
NOTEStep 1: Tighten all bolts to 22 ft. lbs.Step 2: Tighten all bolts to 51 ft. lbs.Step 3: Loosen all bolts, in reverse torque sequence, by 180°Step 4: Loosen all bolts, in reverse torque sequence again by 180°Step 5: Tighten bolts #1 and #2, in the torque sequence, to25 ft. lbs.Step 6: Tighten bolts #3,4,5 and #6, in the torque sequence, 11 ft. lbs.Step 7: Tighten all bolts, in torque sequence, by 80-90°Step 8: Tighten all bolts, in torque sequence, again by 80-90°
The torque specs for a Cadillac depend on which engine it has. For most 425, 572, 368, and 500 engines, the torque for the head bolts is 115 ft. pounds. The torque for the cam bolts is 25 ft. pounds, and the torque for the valve covers is 10 ft. pounds.
Torque sequence------------ l 93157 l l 862410 l ------------ Step 1: torque in sequence to 44 Ft/LBS Step 2: in sequence completely loosen all bolts Step : retorque all bolts in sequence to 44 Ft/LBS Step 4: in sequence turn an additional 90 degrees Step 5: in sequence turn an additional 90 degrees Recheck final torque in sequence***CAUTION*** engine uses Torque To yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.
in sequence torque bolts to 20nm, then again in sequence turn a futher 120 degrees, and again in sequence 120 degrees.
{| |- | NOTE Step 1: Tighten all bolts to 22 ft. lbs. Step 2: Tighten all bolts to 51 ft. lbs. Step 3: Loosen all bolts, in reverse torque sequence, by 180° Step 4: Loosen all bolts, in reverse torque sequence again by 180° Step 5: Tighten bolts #1 and #2, in the torque sequence, to25 ft. lbs. Step 6: Tighten bolts #3,4,5 and #6, in the torque sequence, 11 ft. lbs. Step 7: Tighten all bolts, in torque sequence, by 80-90° Step 8: Tighten all bolts, in torque sequence, again by 80-90° |}
The torque sequence for a single cylinder Briggs and Stratton engine horizontal shaft head is increments of 2's for hp and 1's for head bolts. That makes 11 head bolts for an 18 hp.
torque for bolts upper intake 1999 ford taurus 3.0 dohc
For my Mercury Cougar with Aluminum Heads it is:Torque Sequence 1993 3.8 Cougar; Looking at Engine from front of car the lower bolts are 7 3 1 5 upper bolts are 8 4 2 6. Step 1; Torque in Sequence to 37 FT./ LBS Step 2;Torque in Seq. To 45 FT./LBS. Step 3; Torque in Seq. To 52 FT,/LBS. Step4; Torque in Seq. To 59 FT./LBS. Step 5; Back off all bolts in Torque Sequence 2-3 turns. Step 6; Retorque all Bolts in Sequence 11-18 FT/LBS. Step7; Rotate Long Bolts 85-105 Degrees, Short Bolts 65-85 Degrees in Sequence. Recheck final Torque in Sequence. When replacing Head Gasket be sure to replace all torque-to-yield style Head Bolts. Hope I Have Helped -u-. "Odie" OdiebuiltMC@aol.com
which one? The head bolts? Engine to transaxle? And, are you really asking what the tightening sequence and/or torque rating is?
Torque Sequence 1993 3.8 Cougar; Looking at Engine from front of car the lower bolts are 7 3 1 5 upper bolts are 8 4 2 6. Step 1; Torque in Sequence to 37 FT./ LBS Step 2;Torque in Seq. To 45 FT./LBS. Step 3; Torque in Seq. To 52 FT,/LBS. Step4; Torque in Seq. To 59 FT./LBS. Step 5; Back off all bolts in Torque Sequence 2-3 turns. Step 6; Retorque all Bolts in Sequence 11-18 FT/LBS. Step7; Rotate Long Bolts 85-105 Degrees, Short Bolts 65-85 Degrees in Sequence. Recheck final Torque in Sequence. When replacing Head Gasket Besure To Replace all Head Bolts. Hope I Have Helped -u-. "Odie" OdiebuiltMC@aol.com