Best Answer

This just happened to my 91 mx6. Wouldn't run with any power. Would only run at higher rpm. Mine turned out to be the rubber Accordion air intake assembly. Over time the rubber becomes brittle and breaks which allows outside air to be drawn in. The mechanic told me this air is not metered by the mass flow meter, hence the computer can't calculate the correct amount of gas. Mine was broke on the accordion ribs. This is made to flex as the engine torques. He tested it with a piece of Duct Tape over the open broken area, then ordered the assembly. About $70 for the part, another $70 for diagnose and install. Of course duct tape may do the job.

User Avatar

Wiki User

โˆ™ 2005-03-26 18:45:25
This answer is:
User Avatar

Add your answer:

Earn +5 pts
Q: What is wrong with a 1991 Mazda 626 that is jerking in 1st 2nd 3rd and 4th gear and stalls when the RPMs get low?
Write your answer...

Related Questions

How do you remove brake drum on 1991 Mazda 323?

how do remove the brake drum on a 1991 mazda 323

When was Mazda Navajo created?

Mazda Navajo was created in 1991.

Your 1991 Nissan Pickup squeals and stalls at idle?

belt is loose.

How to hot wire ignition of 1991 Mazda protege?

Can someone please tell me how to hot wire the ignition of a 1991 mazda protege?

What is the factory tire size for a 1991 Mazda 626?

A standard 1991 Mazda 626 was originally equipped with 185/70-14 tires. A 1991 Mazda 626 Turbo came originally equipped with 195/60-15 tires.

1991 Nissan Truck squeals and stalls at idle?

check your alternator belt,and your pulleys ,

Is there clutch adjustment on a Mazda 1991 929?

It is important to know as much as possible about the car that it is driven. Yes, there is a clutch adjustment on a 1991 Mazda 929.?æ

How many quarts in a 1991 Mazda 323?


When did the Mazda rx7 convertible come out?


Where can I get computer repair or exchange for 1991 Mazda B2600 pickup?

well u could send me an email and tell me wat is wrong with your computer...Also what is wrong with your truck and why you want to trade for repair service.. dave

How do you install ignition switch on 1991 Mazda Navajo?

How to remove ignition switch on a 91 Mazda Navajo

Why is my1991 Mazda truck surgingat higher speeds?

why is my 1991 Mazda truck surging at higher speeds

What is wrong with my 1991 Mazda 323 automatic it made a loud thunk then stopped driving there is no acceleration you push the gas pedal and the car doesn't move?

maybe the engine fell out

Where can you find a fuse box diagram for a 1991 Mazda 323?

You can find the 1991 Mazda 323 fuse box diagram at your local Mazda dealership. You can also find the fuse box diagram on the inside cover of the fuse box.

Where is the obd port on a 1991 Mazda Protege?

it doesn't have one

When was the Mazda MX3 first produced?

The Mazda MX3 was first produced in 1991. It was introduced at the Geneva Motor Show in March of 1991. The MX3 was produced until 1998, when production was halted.

Are 1991 Mazda and 1992 Mazda parts interchangeable?

That would all depend on what model you are refering too. 1991 and 1992 Mazda 323 parts are all interchangable (there may be a few exceptions). If your refering to another model, someone else will have to address that aspect.

Where is the thermostat on a 1991 Mazda b2600?

follow the upper radiator hose

Can you put a 2.8L Nissan engine in a 1991 Mazda B2200 pickup?


How much does a 1991 4 door Mazda 626 weight?


Where is the battery in a 1991 Mazda miata?

Trunk right hand side

Where is the fuel filter on a 1991 Mazda b2600i?

on the firewall passenger side

Mazda mpv 1991 have interference engine?

No it is a non-interference engine

How do you change a slave cylinder on a 1991 Mazda MX-6?

How do you change a slave cylinder on a 1995 Mazda B2300 2wd?

Where is the location of the safety fuel shut off on a 1991 Mazda mx6?

The safety fuel shut off location on a 1991 Mazda MX6 is under the dash. It is on the far right side in front of the passenger seat.