0
What size bolts hold the pulley to the water pump on a 99 durango?
Wiki User
∙ 15y ago
5/16 in bolt. use a 1/2 inch wrench.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you put on a water pump pulley for the serpentine belt on a 1995 Chevy Lumina minivan?
there should be 3 or 4 bolts that hold pulley on, just remove these bolts a pulley should come off. but remove belt first ! if pulley keeps turning while removing bolts. you can hold it stationary with a scredriver or similar.
How due you remove the water pump pulley from a 1997 Chevy venture the pulley turns every time you try to undo the bolts?
put the belt back on and hold the pully with your hand while losing the bolts with a wrinch
Does the pully have to be pressed on the water pump of a 1994 dodge spirit?
my 93 with a 2.5 uses 3 bolts to hold pulley on the pump
How do you replace water pump on Chevy impala 2004?
To remove the water pump, first, make sure engine is cool and no pressure in the system, remove the belt. Then hold the pump pulley tightly and remove the 4 10mm bolts that hold on the pulley. Tap the pulley to remove. Then remove the 5 5/16 (or 8mm) bolts that hold the pump. Be sure a drain pan is under the car to catch the coolant. Clean the mounting surface of old gaskets. Install new pump, pulley, belt, and bleed the system
How do you remove 89 Chevy Celebrity 2.8 L water pump using clamp where do you get and how do you use the clamp?
I have changed the water pump on several engines that use that pump, and I never needed or used a clamp. The only possible use that comes to mind would be to clamp on the pulley to keep it from turning so the bolts that hold the pulley on could be taken out. You have to take the pulley off to get to the bolts that hold the water pump in place. The replacement pumps I used did not come with a new pulley so the old one had to be reused.
How do you repair a crankshaft pulley for a 98 Saturn SC2 DOHC?
u need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removalAnsweru need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removal Answeru need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removal
How do you get the water pump pulley out of a 1992 Buick Century?
start with the serpentine belt still on to hold the pulley while you loosen the four small bolts on the front. If it still turns, wedge a flat bar or wrench handle across two bolt heads to hold it still.
How do you remove the fan pulley from the water pump in a 1978 F150?
pully wheel should come off with fan when you remove 4 bolts that hold fan to waterpump
How do you get the radiator fan off of a 2001 dodge durango with a 4.7 engine?
36 mm wrench, and a spanner to hold the pulley. Turn to the left.
What is the torque specification on a water pump for a 1998 buick skylark wth a 3.1 liter engine?
According to the chilton manual the 5 water pump bolts torque to 89 inch pounds. The four bolts that hold the water pump pulley torque to 18 foot pounds.
Replacing water pump on 3.1 liter motor my motor is sideways would like to know how many screws it has on it.?
Remove belt than 4 bolts for pulley than 5 or 6 screws hold the pump to the timing cover.its the ony pulley with 4 bolts holding it on,its an easy job.
How do you pull a damper pulley from a Chevy 350?
If you are just removing the pulley, Then just remove the bolts that hold it on being sure to remove the bolt that is in the middle of the pulley too. Then take a hammer and knock it off.
