Auto Parts and Repairs
Car Computers and Sensors
Saturn S-Series
Crankshaft Sensors
Chevy Blazer S-10

Where do you replace the Crank Position Sensor in a 1993 Oldsmobile 88 Royale?

363738

Top Answer
User Avatar
Wiki User
2004-10-28 20:34:40
2004-10-28 20:34:40

on the front of the motor under the front crank it has a plug going to the crank.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

where is the camshaft position sensor located on a 1999 Oldsmobile intrigue

User Avatar

show location of camshaft position sensor for 2002 Oldsmobile bravada.

User Avatar

It is pretty technical and special tools are needed. Take it to a garage.

User Avatar

You have to dismantle the entire engine,,,NO YOU DO NOT ITS JUST YOU HAVE TO DRAIN THE OIL TAKE THE OIL PAN OFF AND GET THAT DANG SENSOR TAKEN OUT THEN REPLACE IT!!

User Avatar

The 1998 Oldsmobile Intrigue throttle position sensor is held in place with two retaining screws. Remove the retaining screws and the wiring harness. Reverse the process to install the new throttle position sensor.

User Avatar

on a 90 olds 88 royale your sensor sits inside the timing cover...will need to remove the harmonic balancer (need pulley for that) and remove two screws to take sensor out. replace all parts same way they came out and in same order. passenger side of engine in timing cover

User Avatar

how to replace the throttle position sensor on a 97 nissan altama

User Avatar

The Camshaft Position Sensor is located behind the Power Steering Pump.

User Avatar

In order to replace the camshaft position sensor, you would need to disconnect the electrical plug holding it in. Using a socket, hold down the bolt and remove the camshaft position sensor.

User Avatar

how to remplace position of oxigen sensor

User Avatar

how do you replace the camshaft position sensor on a 1997 plymouth voyager 3l

User Avatar

---------------------------------------------------------- The camshaft positioning sensor is hidden behind the starter motor on the 3.5 6-cyl. engine. I think it's the same for the 4.0. The starter motor must be removed to replace the sensor.

User Avatar

Its either your cam shaft position sensor or the crank sensor.

User Avatar

How to replace throttle sensor kia spectra 2003

User Avatar

Never heard of an "ignition sensor". Do you mean oxygen sensor, or maybe crank position sensor, or cam position sensor? There is an ignition "module" also... The oxygen sensor is on the exhaust manifold. The crank posiiton sensor is on the backside of the block. The cam position is on each head.

User Avatar

It is located above the starter. you must remove the starter for access. Make sure you disconnect the battery first.

User Avatar

Where is the crank position sensor 0n a 2001 mitsubishi Galant

User Avatar

it is right above the oill filter just to the left

User Avatar

how to replace the crankshaft position sensor located in a 2003 kia rio

User Avatar

The camshaft position sensor is located near the thermostat housing. You should replace the crankshaft position sensor as well. This one is much harder to locate....it is on the backside of the engine that is between the firewall and the engine block. Both use the same sensor.

User Avatar

On the 3.8 litre engine its located on the forward side under the harmonic balancer. You need to pull the balancer to replace the sensor. The magnetic pick-up on the sensor rides in the stainless steel stotted track on the rear of the balancer.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.