EGR Systems
Ford Expedition XLT
Ford F-150
Late Model 1979-New Ford Mustangs

Where is the EGR valve on a 1999 Ford Mustang 3.8L?

345

Top Answer
User Avatar
Wiki User
Answered
2008-08-28 03:05:57
2008-08-28 03:05:57

it is right in front of the engine by the pully system....it is a squashed sphere on top

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


haynes repair manuals are good but you can go to autozone.com and they have online repair manuels as well it a good site for a lot of information on repair work.

They always blow the head gaskets between 70 and 100 thousand miles.

there should be a sticker under the hood of the car that tells you what the gapping should be. .60

38L is 10.04 US gallons.

Five quarts including filter. My owners manual says 5.75, including filter. My experience agrees with the extra .75 quarts! :)

Yes , on a 1998 Ford Windstar the fuel pump shut off switch ( inertia switch ) is in the drivers footwell behind the kick panel by the drivers left foot , by the inside hood release ( there is an access hole in the panel )

it's located on the firewall right in back of the intake

Not very easily if at all, and why would you want to?

Yes you can, you will need to buy a y pipe either at autozone or your nearest parts store. You will also need to buy 2 mufflers flowmasters are my choice but you decide what you want. then buy some cool tips and there you go.

If you mean 3.8 Litre engine, the answer is 200 horsepower, from the factory. 225 lb/ft of torque.

76l for the first fish and 38l for each additional fish so 266 litres.

There is a relay on the top of the compressor that allows the clutch to engage. Check to see if it is bad by removing the relay and use a wire as a jumper while the car is running to see if the clutch engages. If the clutch engages once the jumper is in place then the relay is bad it cost under twenty dollars to replace.

Fuel injected. fuel injected. the 3.8 liter was never carb. it was in the 80's in other GM vehicles

It seems it may have been bad gas. After some gas treatment and an oil change it gradually improved in three or four days and then stopped completly.

There are 460 CID engine swap kits on SUMMITRACING.COM. The 460 is the building "block" for several larger stroker motors. It will take a lot of work. If you have all the necessary parts, it would take the average mechanic at least 6 weeks. Likely more. Unless you're going for a strictly track vehicle, you'd get more bang for your buck with a supercharged 4.6 or 5.0.

Divide 10 by 38. _ _ ._ _ 38l 100 38 can't go into 10 so add a decimal+zero Then do your basic division. This was coming from a 6th grader.

If the gauge is reading full (pinned as we call it) it can be a ground to the sending unit or the wire going to it is broken ,,this will cause this..Sending unit wires are on top of the tank some times you can see it (or the wires that go to it )test them there you'll need a good meter!!If you want to see what it looks like go to a parts shop and get them to show you one

One of the best places to start could be a dealership. If you don't want to go that route you can always look it up using a Haynes or Chilton repair manuals.

It shouldn't idle that high the factory idle setting is around 900 RPM's check to make sure nothing is sticking and check vacuum lines. Good luck fixing your problem.

The mass air flow sensor is located in the throttle body housing on the 3800 engine. There should be 4 screws that hold it down to the housing. Once they screws are removed, the sensor lifts off of the throttle body.

There is not significant difference between rest cardiac output but during the load amateur heart pumps 18-24 l/min, professional heart pumps 32-38l/min.

Where was the leak coming from? the coolant has some pathways that go to the intake. that's to warm up the air.the most important question is where the coolant was leaking from?

Hard to say what a fair price is.Some guys might do it for $100 while others, like me would not do the job, because it will not solve your problem for very long.If those bearing are gone, chances are that the motor will need a complete overhaul. Rather than paying to overhaul an engine, I would buy a long block from advance auto or autozone OR get one from a wrecking yard who will give a guarantee that it runs.Replacing the bearings is just going to be a waste of your money regardless of what someone charges.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.