Best Answer

most likely on the side of the engine and near the oil filter, it will have one wire going to it with an L shaped push-on connector.

User Avatar

Wiki User

โˆ™ 2006-09-25 21:44:41
This answer is:
User Avatar
Study guides
See all Study Guides
Create a Study Guide

Add your answer:

Earn +20 pts
Q: Where is the oil pressure switch on a 1988 Ford Ranger 2.9L engine?
Write your answer...
Related questions

Where is the power steering switch located?

were is the power steering pressure switch on a 1988 oldsmobile cutlass 2.8 engine

Where is oil pressure switch on 1988 celebrity?

The location of the oil pressure switch depends on which engine the car has. On the 2.8L V6 the oil pressure switch is on the side of the block below the exhaust manifold on the radiator side of the engine. On the 2.5L 4 cylinder engine the oil pressure switch is located on the side of the block below the intake manifold.

Does a 1988 Chevy C10 with EFI have an oil pressure switch that shuts off the fuel pump if the oil pressure is low?

no, however the fuel pump has a secondary route through the oil pressure switch.If the fuel pump relay goes out the pump will run through the oil pressure switch after the engine gets oil pressure. this results in extended engine cranking time before the engine will start

Where is the map sensor located on a 1988 ford ranger 2.9l?

On the engine.

What should the fuel pressure be on a 1988 ranger 2.9?

30 to 40 psi

Where is the multi purpose switch 1988 ford ranger?

The multi function switch is inside the steering column , for turn signals etc.

Where is the ac high pressure cutoff switch located at on a 1988 suzuki samurai?

it does not have a high pressure switch all it has is a evaporator temp sensor/switch.

How much horse power does a Ford Ranger XL 1988 2.9?

I believe the 2.9 liter V6 engine in a 1988 Ford Ranger is rated at : ( 140 horsepower )

How do you make the pressure switch work on a 1988 coupe deville?


Where is the starter located on a 1988 Ford Ranger truck?

Lower rear end of the engine

What is the oil capacity for a 1988 ford ranger 2.9 v6 engine?

5 quarts

On a 1988 ford ranger where is the oil pan?

The oil pan is bolted to the bottom of the engine

V6 2.9L Ford Ranger 1988?

Yes , there was a 2.9 litre V6 engine available in a 1988 Ford Ranger , as well as the 2.0 and 2.3 litre four cylinder engines

Where is oil pressure switch on a 1988 dodge ram d100?


1988 pont firebird 305 engine No oil pressure on gage I have changed the oil switch above the oil filter but no change is there another switch or valve that needs to be looked at or?

Hey, I also had a 1988 firebird and i had the same problem... I replaced a part called the oil pressure sensor and it worked. Hopefully this helps out.. Just dont blow ur trans.. like i did. Good luck

Where is he oil pressure switch on a 1988 Honda Accord?

trying rack down a leak

What should be the oil pressure on a 1988 GM engine 305 tbi?

The oil pressure may vary depend on mileage. However, typically on a 1988 GM engine should be around 14.25 ohms or more.

How do i replace a speedometer cable on a 1988 ford ranger 4wd with a 2.9 engine?

You can replace the speedometer cable, on your 1988 Ford Ranger, by loosening the cable nut on each end of the cable. The cable will come off and can then be replaced.

What is the firing order on a 1988 ford ranger 2.0 liter engine?


Why cant i get fuel to engine on a 1988 ford ranger?

Either change fuel filter or fuel pump...

How do you remove and replace a power steering pressure switch on a 1988 Chevrolet Celebrity?

The power steering pressure switch screws in. Simply unplug the wire harness, unscrew the old switch and screw in the new switch. Plug the wiring harness back in.

Water pump for a 1988 Ford Ranger at?

i need help with the temp.gage in a 1988 ford ranger

Diagram of a fuse box for a 1988 Ford Ranger?

diagram of fusebox on 1988 ford ranger

How do you rebuild a 1988 ford ranger 23L engine with fuel injection?

Take it to jasper they rebuild any motor.

Where is the fuel pump relay on a 1988 Jeep Cherokee Laredo?

The 1988 Jeep Cherokee fuel pump relay switch is located on the firewall in the engine compartment. The switch will be on the drivers side of the firewall.