0
Would it be possible to change out a 2.8L for a 4.3L in a 86 S-10 4X4 Blazer?
Wiki User
∙ 17y ago
Yes, as long as you change the Tranny with it. and you need the wiring harness, computer, radiator, fan, hoses, motor mounts, transfer case, front driveshaft, exhaust manifolds, headpipe, cat. converter,
Wiki User
∙ 17y ago
Yes, it is possible to swap a 4.3L engine into an 86 S-10 4X4 Blazer that originally had a 2.8L engine. However, this type of engine swap may require modifications to the engine mounts, exhaust system, wiring harness, and possibly other components to ensure proper fitment and functionality. It is recommended to consult with a professional mechanic or engine swap specialist to plan and execute this type of swap successfully.
Add your answer:
Earn +20 pts
Where is the starter on a 1987 Chevrolet Blazer S10 with a 28L V-6 motor at?
under exaust manifold on passenger side
What does the ditloid 28L in the WA mean?
28 Letters in the Word "Antidisestablishmentarianism"
What is the correct timing for a 1986 Chevy Camaro 28L?
The order is 1,2,3,4,5,6
Where is the oxygen sensor located on a '89 Beretta w 28L V6?
it should be located on the rear manifold
The hypotenuse of a right triangle is 26 feet long One leg is 14 feet longer than the other Find the length of the shorter leg?
Let the length of the shorter leg be L, then the longer leg is L + 14.By Pythagoras then 262 = L2 + (L + 14)2 = L2 + L2 + 28L + 196 = 2L2 + 28L + 196676 = 2L2 + 28L + 196 : 2L2 + 28L - 480 = 0 : L2 + 14L - 240 = 0This can be factored : L2 + 14L - 240 = (L + 24)(L - 10) = 0As only a positive number answer applies and this is when L - 10 = 0 : L = 10.The length of the shorter leg is 10 feet.
How many psi is the fuel pump on a 1988 buick century custom v6 28l fi?
Should be around 40 psi
What is the fuel on 1983 S-10 28L?
gasoline-usually 89 octane. fuel filter is in the rochester 2se carburetor on a 2.8l 1983 Chevy motor.
What are some causes and remedies for an 86 Jeep Cherokee with a 28L V6 with a very high CO output?
First, check your air filter and O2 sensor. Both probably need to be replaced. If the HC is up, change the plugs and wires too. If the vehicle is carburated you probably don't have an O2 sensor.
Where is the map sensor located on a 85 camaro 28l?
should be a small black plastic box close to the distributor mounted on a bracket. it will have a couple of wires and a vacuum line the runs to the intake manifold
28l beretta what sensor is located under throttle body but on engine by to small coolant lines spewing oil from it you pretty sure not oil pressure sensor?
could be tps or throttle positioning sensor
What does it mean when you have low levels of Immunoglobulin G Qn Serum?
what does it mean when my IGM is low at 28L
87 Chevy S10 28l V6 and one lifter collapsed and warped the pushrod Can you just change that one bad lifter and do you have to take off the intake manifold to get the lifter out please help?
You can change just the one lifter, however you should determine why it went bad. The intake manifold must come off to get to the lifter. Is there advanced mileage? do you change the oil regularly? Seeing how it is an 87 vehicle, with 19 years of use on the engine, I would strongly suggest changing the full set. Be carefull though as there is the possibility on that engine of 2 different size lifter bores. If yours are oversized it will be stamped on the lifter bore (not on the lifter) 0.25mm 0.5 There should also be a white paint mark at the bore.
