0
Your 1993 wrangler 40L inline six will crank and rollover but will not start replaced distributor wires plugs starter ignition coil map sensor throtle position sensor fuel pressure good?
Wiki User
∙ 15y ago
If it's not the crank sensor, it's probably the ECM, and that's bad. Try you crank shaft position sensor, if it is bad the engine will not run. It's on the back of the engine just below the vavle cover on the drivers side
You can also try the ignition pickup. It's a little back plastic plate that sits on top of the distributor when you take the cap off.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Where is the ignition condenser located on a 2003 Toyota Highlander?
The ignition condenser is located inside the distributor. In order to repair the issue, the distributor will need removed and replaced.
1996 Jeep Cherokee that turns over but will not start no spark to the distributor or the spark plugs replaced the ignition coil and the pick-up coil in the distributor Engine is getting fuel?
The most common failure associated with those symptoms is the Crankshaft Position Sensor.
Why would a geo prizm not have spark engine Turns but does not start replaced entire distributor 3 times already all components are located inside arent they Crankshaft position sensor?
the cam position sensor and ignition coil are inside the distributor. the crank position sensor is located on the bottom front of the engine, behind the belts on the left side.
1989 Mazda will not start it is getting fuel and has a good spark from the coil to the distributor cap but has a week spark at the plugs Have replaced ignition coil distributor pickup coil plug wires?
try to get a new ignition rotor
1974 pickup 390 mtr has been converted to electronic ignition The ignition fried Replaced ignition and coil Ignition switch is good but still no spark Can anyone help?
You'd have to describe the components you replaced. Did you use a plug and go all in one distributor or did you replace the coil, distributor, and add an electronic ignition unit? If you "fried" your ignition, it's likely you fried something else along the line too. Check all your components.
Why would there be no spark when I have already replaced the coil the crank position sensor and the ignition module on a 1987 Nissan d21 pickup with 3.0 engine?
The computer maybe fubar(no good)? have you checked the plug wires distributor cap and rotor? could be the distributor its self or possably the pick up coil
Why does your 84 z die when accelerating Ignition coil has been replaced fuel pressure is good Is there a sensor doing this?
You have an ignition Control Module that you can check that controls ignition timing Throttle Position Sensor that tells the computer where the throttle is so it can regulate and give the correct air fuel ratio.
Find camshaft position sensor on a 3.3 Nissan engine?
The camshaft position sensor is an integral part of the distributor. If codes and tests indicate that it is faulty, the distributor must be replaced. Last I looked a cheap one was $1,500.
1988 ford aerostar no start problem I have had the ignition modual tested replaced the coil replaced the distributor cap and rotor and stil no spark please help?
replace wire from coil to distributor or inertia switch lower side panel under glove box.
Where is the cam shaft position sensor in a 1999 Mercury Villager?
The camshaft position sensor is integral with the distributor. So, have it checked carefully by a professional because, if the sensor is faulty, the distributor must be replaced. That can get ugly expensive real quick.
How do you replace the ignition coil on a 1990 Honda CRX?
The coil and distributor are one unit, there for, no coil wire. Yes it is a sealed unit and has to be replaced as one.
Your 1987 ford ranger signal lights and heaterair fan blower only come on when the ignition switch is placed in a certain position Now they don't come on at all in any ignition position Why?
Ignition switch worn out and needs to be replaced? After 20 years
