Did you happen to check the turn signal flasher before you installed the switch?
check fuses and relays and flasher and go from there
Need to know the year, make and model vehicle. If the signals are still working, turn on the signals and follow the clicking noise until you locate the flasher.
Check the flasher for the turn signals which is under the dash on the left side of the steering column . It is different from the emergency flasher.
yes i changed all of that but it still is not working so im wondering what else could be causing this
The signals and the emergency flashers have separate circuits, separate fuses, separate flasher relays. Start with checking the fuses, the bulbs, the signal flasher relay and wiring and if it still doesn't work it may be the signal switch is bad.
If you replaced the flasher on your 1999 Mercury Cougar and your turn signals are still not working, you should check the turn signal fuse. This fuse is located under the dashboard on the driver's side of the vehicle to the left of the steering column.
check the bulbs, check the fuse then check the flasher, if they are still dead the signal switch may be at fault.
If you mean the turn signal flasher it is located under the dash near the steering column.If one side still flashes, turn on that sides signals and track down the clicking sound. Often one side will quit working before the entire thing quits. Your four way flasher looks the same but it is a different circuit.AnswerThe flasher is an electronic device incorporate with the hazard warning switch. It is selected thru turn-signal switch when "H" switch is out. It is refered to as a timer. The relay switch for your turn signals is located behind your hazard light flashers. It is literally DIRECTLY BEHIND the button used to turn the emergency lights on and off.
have you tried replacing the flasher u need to replace the flasher can for the turn signals there are 2 one for hazards and one for turn signals usually found in the fuse box, and cost about 3 bucks
Could be turn signal flasher Could be problem with switch in steering column Could be turn signal flasher Could be problem with switch in steering column
u need to replace flasher can in your vehicle This could happen if flasher had hazzard flasher "on" and could be broken so it will not turn off. (I assume center brake light still works) if so, need new flasher switch in steering colum or find a way to rewire brake lights from brake light switch to rear lights. This is just a guess. Be sure brake light switch is OK.
The directional signals and the emergency flasher each have their own flasher unit. They are the same type of flasher and should be beside each other under the dash.
More detail: the turn signals slowed down gradually and then stopped working. All lights still flashed when hazard lights switch was activated. The bulbs and fuses are all okay, and I have replaced the hazard flasher (which I think is a combo hazard/turn signal unit). Can't see any other flasher unit under the panel, don't know what else to try. Any ideas?
Might be turn signal flasher
Problem: No turn signals or hazard lights. No clicking. Tried the WD40 trick, checked fuses, replaced flasher relay. Still no turn signals or hazard lights. What is next? V Hoffman Might be time to replace the turn signal stalk, also known as the multi-function switch. I have also seen reports of people disassembling the switch and cleaning the contacts. See "Related Questions" below for more
The turn signal switch overrides the brake light circuit while the turn signals are on. If the switch is damaged or worn out the brake lights won't work.
If turn signals are not blinking on the dashboard but they are still working, the cause might be a burned out bulb in one of the blinkers on the outside of the car. There might also be a fuse burned out or bulbs burned out in the dash. Even the flasher can be the problem in this situation.
Replace the turn signal flasher first under the dash near the column but You may have a bad turn signal switch. On your model, the hazards and turn signals use the turn signal switch assembly. New $300+ ;salvage yard $ 40.00.
There is a flasher unit under the dash at the fuse panel but there is also a flasher relay PAC in the trunk just ahead of the spare tire mount. If you replace the underdash unit and it still don't work then check the connections to the relay PAC in the trunk. If that looks good then the relay PAC is bad. New electronic units are still available.
you would need to check for voltage past the flasher unit and before the flasher make sure the problem is not the switch, or the wiring after the flasher.
It could be the turn signal bulbs, some vehicles use separate bulbs for the hazard and turn signals. It could also be a bad switch or wires for the turn signals.
blower motor in dash was not working replaced it still not working now what
check your fuses
Check the bulb and the flasher. Check the bulb and the flasher.