How do you replace the headlight bulb located on a 1999 Ford Expedition?

Answer 1

Push headlight retaining housing retaining clips (rectangular metal tabs located above radiator wall and to outside and rear or headlight)rearward, then upward to release headlight assembly. Pull headight assembly forward from body. Unscrew bulb retaining ring. Remove bulb from headlight housing. Remove bulb from socket wiring by pulling straight out. Insert new bulb into socket wiring (use paper towel to avoid touching bulb). Reinstall by reversing removal instructions.

you also may have to loosen the air filter assembly and remove the air intake flange (rubber part) to gain full access to the screw holding the coolant tank.

Answer 2

Open the hood and find the two metal tabs located right behind the headlight. They are vertically oriented with a 90 degree bend at the top. Pull straight up on them to release the headlight lenses. I believe the bulbs pull straight out. Caution: when installing the new bulbs be careful not to touch them. Any oil or dirt on the bulbs may damage them.

Answer 3

It has a picture in the owner's manual which shows how to do this. 1) Open the rear hatch. 2)Take the two screws out of the light assembly. 3) Pull the assembly out. This will take a little effort because there are two plastic fasteners holding the assembly. 4) Turn the light holder and remove. Hope this helps.

Answer 4

***CAUTION***The halogen bulb contains gas under pressure. The bulb may shatter if the gas envelope is scratched or if the bulb is dropped. Handle the bulb carefully. Grasp the bulb only by its base. Avoid touching the glass envelope. è The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp. Headlights Removal & Installation 1. Raise and support the hood. 2. Raise the headlamp retainers by pushing rearward and pulling up. 3. If equipped, rotate the headlamp bulb protective counterclockwise and remove. 4. Disconnect the headlamp bulb electrical connector. 5. Remove the headlamp assembly. 6. Rotate headlamp bulb retainer counterclockwise and remove. 7. Remove the headlamp bulb by pulling it straight out with a gentle up-and-down rocking motion. ***WARNING*** Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation. To Install; 8. Install a new bulb into the headlamp assembly. 9. Install the headlamp bulb retainer and turn it clockwise to engage the retaining tabs. 10. Attach the bulb electrical connector. 11. If equipped, install the headlamp bulb protective cover. 12. Install the headlamp assembly. è Be sure the headlamp assembly is positioned correctly with the alignment pins inserted into the proper holes and onto the ribs of the reinforcement. 13. Engage the retainers by gently pushing down. 14. Turn the lights on and check the bulb operation.

Answer 5

***CAUTION*** The halogen bulb contains gas under pressure. The bulb may shatter if the gas envelope is scratched or if the bulb is dropped. Handle the bulb carefully. Grasp the bulb only by its base. Avoid touching the glass envelope. è The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp. Headlights & Tail Light Bulb Replacement Removal & Installation 1. Raise and support the hood. 2. Raise the headlamp retainers by pushing rearward and pulling up. 3. If equipped, rotate the headlamp bulb protective counterclockwise and remove. 4. Disconnect the headlamp bulb electrical connector. 5. Remove the headlamp assembly. 6. Rotate headlamp bulb retainer counterclockwise and remove. 7. Remove the headlamp bulb by pulling it straight out with a gentle up-and-down rocking motion. ***WARNING*** Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation. To Install; 8. Install a new bulb into the headlamp assembly. 9. Install the headlamp bulb retainer and turn it clockwise to engage the retaining tabs. 10. Attach the bulb electrical connector. 11. If equipped, install the headlamp bulb protective cover. 12. Install the headlamp assembly. è Be sure the headlamp assembly is positioned correctly with the alignment pins inserted into the proper holes and onto the ribs of the reinforcement. 13. Engage the retainers by gently pushing down. Turn the lights on and check the bulb operation.

Answer 6

2000 Ford Expedition turn signal light bulb replacement: Purchase the correct replacement turn signal light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the turn signal light bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).

Answer 7

Hey Mike== You have to remove the light assy and take them out from the rear. GoodluckJoe

Answer 8

twist the black tube (where the wires come out) it will click, remove the bulb holder , replace bulb refit