0
Chevrolet
A brand of vehicle, Chevrolet or Chevy was produced by General Motors Company (GM). The car was named after Louis Chevrolet and was set up to sell a variety of mainstream vehicles to compete with Model T by Henry Ford.
6,429 Questions
What kind of services does Optical Express Provide?
After doing some quick research I found out that Optical Express offers laser eye surgery, eye exams as well as glasses and sunglasses sales. Hopefully this was helpful.
Where is the best place to get deals on Chevrolets?
The best place to find deals on Chevrolets would be actual Chevrolet dealerships (only if you are searching for a new car) or your local trading post, newspaper, or craiglist ad. With Craiglist you must be careful. If you go to look at a car, make sure you take someone with you and meet that person in a public area.
Does Chevrolet offer deals on the Tahoe?
Chevrolet does occasionally offer deals on many of their vehicles including the Tahoe. You would have to contact your local dealership to find out what specials they currently are offering.
When putting new front brakes on a 2005 Chevy Equinox do you also have to adjust calipers?
Cailbers have NO adjustment. They have a piston that moves in and out as the brake is pushed down.
How do you engage into four wheel drive on a 1995 K2500 Chevrolet?
Shift it into either 4H or 4L, and sometimes, after going into 4X4, you need to put the car in reverse for a few feet to engage it.
What is the bearing clearance on a small block Chevy?
Gm advises .001, to .003. If it is going to be a 150,000 mile motor, I go to the tight side of .001. Race motors go to about .002, to .0025. They are more "loose" and rev better. The person that regrinds the crankshaft, controls this. You have to tell him in advance. Remember, "looser" tolerances will need a high volume, as well as high pressure pump, to keep a good pressure level with the larger clearance. The big block Chevy pump works great.
Which way does the distributor rotate on a small block Chevy?
The distributor can be turned both ways. The rotor however, which I suspect you are asking about, turns clockwise on a small block V8.
Does a 350 big cam have more power than a regular 350?
A big cam 350 probably refers to a cummins diesel engine.
Cummins diesel engines had a reputation for cam failure in the past, and the company came out with a fix they called the big cam series of engines, which means the cam bearings, lobes, followers etc were made bigger to last longer
C
Is there a passenger side airbag sensor on 2002 chevy trailbalzer?
normally yes unless the maker was asked to take the air bag out
Can you use supertech ST16 in a 2000 Chevy 6.0 2500?
I would not recommend you use any Supertech filter. This filter may or may not be of excellent quality depending on who the manufacture is, which you have no idea of knowing. Why risk it with an expensive engine. I recommend you purchase an AC/Delco, Purolator, Wix, or Bosch quality filter for your truck.
Is the transmission the same in a 97 Chevy k1500 5.7 as a 97 Chevy k1500 5.0?
YES. They are the same.
Where does the ground wire go on a 1965 chevy c10?
There is usually a bolt hole in the alternator/generator bracket. I believe it is either a 3/8" or 1/2" hole. Stock, the ground wire goes here with a bolt, lock washer, and nut.
If you have an engine that has the alternator on the opposite side of the engine from the battery, use one of the existing bolt holes in the front of the cylinder head closest to the battery. Use a bolt and lock washer to install.
In either scenario, be sure to clean off the paint where the cable end is going to touch the metal. This will ensure a good connection. I tend to use 0 gauge wire for my ground wire. A little bit of overkill, but I like to have a good ground.
How do you remove the shifter from a 1983 chevrolet 4 speed truck transmission?
Under the rubber boot covering the shifter, there should be 4? bolts. Make sure transmission is in neutral and remove these bolts, shifter should be able to be removed at this time
Where is the Chevy Cruze built?
The Chevy Cruze is 'assembled' in the GM Assembly Plant in Lordstown, Ohio. This facility formerly produced the popular Caviler/Sunbird models.
How do you bleed brakes on chevy aveo2004?
1. Place a clean shop cloth beneath the brake master cylinder to prevent brake fluid spills. With the ignition OFF and the brakes cool, apply the brakes 3-5 times, or until the brake pedal effort increases significantly, in order to deplete the brake booster power reserve.
2. If you have performed a brake master cylinder bench bleeding on this vehicle, or if you disconnected the brake pipes from the master cylinder, you must perform the following steps:
3. Ensure that the brake master cylinder reservoir is full to the maximum-fill level. If necessary, add Delco Supreme 11, GM P/N 12377967, or equivalent DOT-3 brake fluid from a clean, sealed brake fluid container. If removal of the reservoir cap and diaphragm is necessary, clean the outside of the reservoir on and around the cap prior to removal.
4. With the rear brake pipe installed securely to the master cylinder, loosen and separate the front brake pipe from the front port of the brake master cylinder.
5. Allow a small amount of brake fluid to gravity bleed from the open port of the master cylinder.
6. Reconnect the brake pipe to the master cylinder port and tighten securely.
7. Have an assistant slowly depress the brake pedal fully and maintain steady pressure on the pedal.
8. Loosen the same brake pipe to purge air from the open port of the master cylinder.
9. Tighten the brake pipe, then have the assistant slowly release the brake pedal.
10. Wait 15 seconds, then repeat steps 3.3-3.7 until all air is purged from the same port of the master cylinder.
11. With the front brake pipe installed securely to the master cylinder, after all air has been purged from the front port of the master cylinder, loosen and separate the rear brake pipe from the master cylinder, then repeat steps 3.3-3.8.
12. After completing the final master cylinder port bleeding procedure, ensure that both of the brake pipe-to-master cylinder fittings are properly tightened.
13. Fill the brake master cylinder reservoir with Delco Supreme 11, GM P/N 12377967, or equivalent DOT-3 brake fluid from a clean, sealed brake fluid container. Ensure that the brake master cylinder reservoir remains at least half-full during this bleeding procedure. Add fluid as needed to maintain the proper level. Clean the outside of the reservoir on and around the reservoir cap prior to removing the cap and diaphragm.
14. Install a proper box-end wrench onto the RIGHT REAR wheel hydraulic circuit bleeder valve.
15. Install a transparent hose over the end of the bleeder valve.
16. Submerge the open end of the transparent hose into a transparent container partially filled with Delco Supreme 11, or equivalent DOT-3 brake fluid from a clean, sealed brake fluid container.
17. Have an assistant slowly depress the brake pedal fully and maintain steady pressure on the pedal.
18. Loosen the bleeder valve to purge air from the wheel hydraulic circuit.
19. Tighten the bleeder valve, then have the assistant slowly release the brake pedal.
Wait 15 seconds, then repeat steps 8-10 until all air is purged from the same wheel hydraulic circuit.
20. With the right rear wheel hydraulic circuit bleeder valve tightened securely, after all air has been purged from the right rear hydraulic circuit, install a proper box-end wrench onto the LEFT FRONT wheel hydraulic circuit bleeder valve.
21. Install a transparent hose over the end of the bleeder valve, then repeat steps 7-11.
22. With the left front wheel hydraulic circuit bleeder valve tightened securely, after all air has been purged from the left front hydraulic circuit, install a proper box-end wrench onto the LEFT REAR wheel hydraulic circuit bleeder valve.
23. Install a transparent hose over the end of the bleeder valve, then repeat steps 7-11.
24. With the left rear wheel hydraulic circuit bleeder valve tightened securely, after all air has been purged from the left rear hydraulic circuit, install a proper box-end wrench onto the RIGHT FRONT wheel hydraulic circuit bleeder valve.
25. Install a transparent hose over the end of the bleeder valve, then repeat steps 7-11.
26. After completing the final wheel hydraulic circuit bleeding procedure, ensure that each of the 4 wheel hydraulic circuit bleeder valves are properly tightened.
27. Fill the brake master cylinder reservoir to the maximum-fill level with Delco Supreme 11, or equivalent DOT-3 brake fluid from a clean, sealed brake fluid container.
28. Slowly depress and release the brake pedal. Observe the feel of the brake pedal.
If the brake pedal feels spongy, repeat the bleeding procedure again. If the brake pedal still feels spongy after repeating the bleeding procedure, perform the following steps:
29. Inspect the brake system for external leaks and pressure bleed the hydraulic brake system in order to purge any air that may still be trapped in the system.
30. Turn the ignition key ON, with the engine OFF. Check to see if the brake system warning lamp remains illuminated.
Is the Chevy 6.2l vortec max engine gasoline or diesel?
The chevy 6.2 vortec max package is a gas engine, however Chevy did make a 6.2 diesel engine that was used for military vehicles. The diesel 6.2 is no longer available.
How do you change sparkplugs on 04 chevy montecarlo?
Turn the ignition switch to the OFF position, then disconnect the negative battery cable.
On the 3.8L (VIN K) engine, the cosmetic/acoustic engine cover, also called the fuel injector sight shield, must be removed. Remove this cover by first turning the tube/oil fill cap counter-clockwise from the valve rocker arm cover. Lift the fuel injector sight shield up at the front and slide the tab out of the engine bracket.
Remove only one spark plug wire at a time to avoid mixing up the wires. Each must be returned to its original location. Note the position of the spark plug wires before removing them. The high energy in these ignition systems can cause induced voltages to fire in adjacent spark plug wires. For this reason, the factory engineers take care to position the wires to minimize "crossfire." Wires should be returned to their exact locations and secured with whatever clips or loom components were originally installed.
Spark plug boots tend to stick firmly to the spark plug insulator. DO NOT pull on the spark plug wire. Pull on the spark plug boot or heat shield only, twisting a half-turn to release the seal while removing. Do not pull on the spark plug wire or it may be damaged.
Using the proper size spark plug socket, remove the plug from the cylinder head.
To install:
Verify that the spark plug is clean, properly gapped and that the threads are lightly lubricated with clean engine oil.
Be sure the plug threads smoothly into the cylinder head and is fully seated. Use a "thread chaser" if necessary to clean the threads in the cylinder head. Cross-threading or failing to fully seat the spark plug can cause overheating of the plug, exhaust blow-by, or thread damage. Follow the recommended torque specifications carefully. Some technicians will place a small piece of rubber tubing (like a piece of vacuum line) on the end of the spark plug and use it to turn the plug, by hand. In this way, if the plug is not threaded properly, not enough torque can be placed on the plug to do any damage.
Torque the spark plug to 11-15 ft. lbs. (15-20 Nm).
Install the spark wire to the spark plug, making sure the connector engages the spark plug and the boot is fully seated.
On the 3.8L (VIN K) engine, install the cosmetic/acoustic cover. Insert the tab of the fuel injector sight shield under the engine bracket. Place the hole of the shield onto the oil fill neck of the valve rocker arm cover. Install the tube/oil fill cap onto the valve rocker arm cover and twist clockwise in order to lock.
How do you unlock a 2010 chevy delco radio?
You have to have the code. This is to prevent someone from stealing the radio and installing it. To obtain the code for the radio, you will have to go to the dealership with your state registration so that they can get it from the manufacture. Once you have the code you can enter it using the number buttons on the radio.
How much freon do I put in my chevy 1999?
as much as you need to untill the gauge gets to the right point.
