0
Construction Tools
This category includes the humble hammer and pliers as well as the more modern equivalents such as nail guns, power saws, and precision laser levels. Tools that a professional construction worker as well as the weekend handy man has are discussed in this category.
2,173 Questions
A spirit level tells if things are horizontal contain alcohol or a re underground?
They tell you if things are horizontal or vertical.
Why does your drill smoke when you use it?
The drill bit is struggling to cope with the task. The drill is probably not powerful enough
What are the dangers of a hand saw?
The dangers of using a hand saw are basically being careful not to cut your own hand that may be holding whatever you are cutting.
It's a very short wrench head that fits on a ratchet driver instead of a socket.
What type of pliers do you need to make jewelry?
You are going to need round nose pliers, flat nose pliers and cutters.You can get them from Walmart or any other hardware store that occupies them.
ANS 2 -You would very likely need all these tools in miniature form also. Sets of 3" pliers and cutters are available less than $ 10 in HD and other tool stores.
What is radial drilling machine?
a machine in which the drilling head is mounted to slide along a radial arm which can be rotated, raised, or lowered on a vertical mast to adjust the position of the drill above the workpiece Often shortened to radial.
How do you clear a jammed nail from a Hitachi NR83A nail gun?
First, unplug the gun from your airline to avoid any accidents. Now remove the front cap of the gun (with a 1/8 allen wrench, I believe on this model) and you will see the jammed nail. Use a small screwdriver or prybar to remove it and then push the piston up. Now screw back the plate and carry on nailing.
What are the safety when use drilling machine?
Clamp your work to the drill table, keep your hands, clothing and hair away from rotating parts, tighten the chuck firmly , when stopping, do not touch the tool till it is totally stopped.
What are sizes of drilling machine?
There are many sizes of drilling machine. the smallest is possibly the Dremel drill and they go all the way up through handheld electric drills to floor drill presses taller than people.
A grab it drill bit is a piece of hardware that attaches to the end of any drill and pulls out stripped or damaged screws that cannot normally be removed with a screw driver or a drill, and would other wise cause damage to underlying material if a hammer was used to forcibly pull it out.
it is plier with a combinition of gripping,cuttingand holding that's why it is called as a combinition plier.
What way do you turn the wrench?
Looking down , you turn clockwise to tighten and the other way to loosen. This is common world wide.
What size wrench would you use for a 58 diameter bolt?
I hope you mean a 5/8 bolt (58 inches would take a machine to turn). Measure your bolt head across the opposing flats. For a 5/8 bolt it may be 1 inch or even larger. The last one I did was in a truck's shock mounting and that took a 1.25 inch socket.
All technicians, electricians, plumbers and handymen use pliers almost every day.
Why must the work be firmly held when drilling on a drill press?
Because if you don't hold it firmly, or better yet, clamp it, the drill bit may grab it and spin it rapidly causing damage and possible injury.
Why Sthil chain saw loses power when cutting?
Sthil?? Chinese cr*p; or Stihl?
This problem can occur on any type of chainsaw (Husqvarna, Dolmar, Solo etc.) and not only on Stihl.
There could be several problems.
1) Maybe the clutch is worn out or even broken
2) Piston rings might be worn out
3) Piston and cylinder might be worn out (these two are very expensive)
4) Fuel filter and fuel lines as well as fuel vent (if there is such on your type of chainsaw) might be clogged
5) Air filter might be clogged
6) Ignition coil might be faulty...
I had a similar problem on my Stihl 041 AV. I replaced the clutch (took the good clutch from 031 AV and installed it on 041 AV - it fits and works great, btw :D) and piston rings.
Whose 65Mn is called in other countries?
65Mn is equivalent to grade 1065 according to SAE J403. As Pressed mentioned, it is often cold-rolled and heat treated to high strength (called spring temper). ASTM A 29 is a standard for bar steel, so it is not appropriate for cold rolled strip. Grade 1065 is one of the grades covered by ASTM A 682 Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled, Spring Quality, General Requirements for.
A step bit is an angled bit which can drill several different diameter holes, depending on how deep you push it. Electricians use them often for drilling into panels. You can find them in the electrical section at your closest building store. Expect to pay 30 to $50 for a good one.
Different between claw hammer and peen hammer?
A claw hammer is used for pulling nails and is most commonly used by a carpenter or other wood workers A pien hammer is used by blacksmiths, mechanics and other metal workers.
