0
Construction Tools
This category includes the humble hammer and pliers as well as the more modern equivalents such as nail guns, power saws, and precision laser levels. Tools that a professional construction worker as well as the weekend handy man has are discussed in this category.
2,173 Questions
A basin wrench is a tool to remove and replace the nuts that hold a faucet in place. It works in tight, low visibility places for sink repair. The basin wrench looks like a long steel bar with a claw on one end. This claw is usually spring loaded to keep a tight grip of the nut being turned, and can 'flip' to enable turning either way easily. The other end makes a "T" as a smaller bar goes across it.
Is chisel a electrical hand tool?
Chisels are almost always a static hand tool, or a pneumatic one. I suppose electric is possible, but haven't seen one yet.
Which table saw do you need to cut tile?
You need an actual tile saw. You can probably rent one at your local hardware store.
ANS 2 - Tile is best cut with a water fed saw, or at least one where the bottom of the blade runs through a container of water. Cheap electric tile saws are now common and useful for occasional tile jobs. I bought one 3 years ago for $89 and spent $29 on a reasonable 8" diamond blade. It's lasted me through 8 complete bathroom renos and two tiled kitchen floors. Keeping the blade wet and cool is the key.
We just paid $12.00 for this attachment today at an antique shop. Should be worth a lot more.
They are pliers with a very wide gripping end, often converted from vice grips. I have 3 different with 2, 4 and 6 inch wide blades. Not strong, but capable of putting a very good bend on thin steel or alloy sheet.
How thick should the tip be on a standard screwdriver?
Is there a standard ? - I have screwdrivers in 5 flat sizes ranging from 0.75 mm x 2mm wide, up to 2.5 x 18mm.
When do you use theodolite for surveying?
To measure Angles, Process of Measuring Horizontal and vertical Angles
Looking for specifications on Hilti Hit - RE 500 Epoxy?
I'm struggling to upload the pdf format for you.
You can look it up at hilti.com or contact your nearest Hilti Centre for the info you are looking for
Hope it helps...
off set
I have many different hammers. I keep 6-8 of them in my workshop and 1 in each vehicle.
What looks like a pair of bent needle nose vise-grip pliers?
That's most likely a pair of bent needle nose vise grip pliers. I have a set just like that and also others with wide flat jaws and large round jaws. There are many different kinds if vice grip pliers.
What limits the size of drill bit that can be used on a bench drill?
The size of the chuck is the only limitation. Most bench drills have a 1/2 chuck and many of them are removable. -ie,you can often fit a bigger chuck.
no, ive seen chainsaw wounds, a number of them, imagine what it would look like if a lion mauled a human, multiply that by 10 and you have a chainsaw wound, they don't cut flesh, they shred it
Where can you buy a Swedish saw?
A Swedish saw can be seen in most hardware stores and in Home Depot and Rona. It's a metal framed bow saw, with a blade from 18" to 36 "long. It's main use is to lop branches off trees. The blades have large offset teeth and are disposable.
How could you increase the MA on a screwdriver?
Increase the diameter of the handle, the diameter of the handle is greater than the diameter of the screw so by increasing the diameter of the handle you arerequiredto use less force.
What is the function of a socket wrench?
The function of a socket wrench is to tighten or loosen nuts and bolts. It does this better by completely encompassing all sides of the nut.
What is a 16 mm wrench in standard?
16mm is almost exactly 5/8. The wrenches are interchangeable on most bolts.
What is one that works with metal anvil and chisel?
A person that works with metal anvil and a chisel is called a blacksmith. Blacksmiths are rare now, but in the days when horses were a common mode of transport, the blacksmith made horseshoes, wagon wheels and other metal parts.
What are safety tips for drill press?
Clamp your work to the table. Don't put your hands on or near the chuck while it's rotating. If you have long hair,keep it out of the way. Always make sure the drill bit or tool is tightened into the chuck.
What materials are machined by low helix angle drill bit?
low helix angle drill bits are used for machining hard materials
How do i fix my craftsman drill press if the chuck falls off is it pressed on?
first, has it been damaged, if no, then clean both parts as best you can, then use some chalk like the kind used in chalk lines, put a lite coating on the tapered part of the chuck, and put it in place, stack some wood under the chuck and use the drill press to gentle force the chuck in place. shoud last along time.
ANS 2 Your average drill press chuck is held on to the spindle with a Morse Taper. To fit this simply clean both parts and tap it lightly on with a soft face hammer. The idea is that it can be changed quickly for other sizes.
