Dodge and Plymouth Neon

Yes, a 2005 Dodge Neon SX 2.0 transmission should fit in a 2003 Dodge Neon SX 2.0, as both vehicles share similar engine and transmission designs from the same generation. However, it's important to verify compatibility regarding specific components like wiring harnesses and transmission control modules. Always consult a professional or reference service manuals for any potential differences or required modifications.

Code 52 on a 1998 Dodge Neon typically indicates a problem with the powertrain control module (PCM) or the circuit related to it. To fix this, first check the PCM connections for corrosion or damage, ensuring they are clean and secure. If the connections appear fine, you may need to test the PCM itself for proper function, which could involve replacing it if it’s faulty. Additionally, inspect related wiring and sensors for any issues that could affect the PCM's performance.

To remove the camshaft from a Dodge Neon, first, ensure the engine is cool and disconnect the battery. Then, remove the valve cover, timing belt or chain, and any associated components that obstruct access to the camshaft. Carefully unbolt the camshaft caps in the correct order, lift the camshaft out, and be cautious of any shims or spacers that may be present. Finally, inspect the camshaft and related components for wear or damage before reassembly.

A tire on a Dodge Neon can smoke due to excessive friction caused by rapid acceleration, hard braking, or making sharp turns. This friction generates heat, which can cause the rubber to overheat and produce smoke. Additionally, under-inflated tires or worn tread can increase the likelihood of smoking. If the car is experiencing mechanical issues, such as a misaligned wheel, that can also contribute to tire smoking.

The starter bolts on a 1998 Plymouth Neon are located on the transmission side of the engine, securing the starter motor to the transmission bell housing. You will typically find two bolts, which may require a socket wrench to access. To reach them, it may be necessary to remove any obstructions, such as the air intake or other components, depending on the specific configuration of your vehicle. Make sure to disconnect the battery before attempting any work on the starter.

To fix a P0440 or P0441 code on a 2003 Dodge Neon, start by inspecting the fuel vapor system for any leaks, particularly in the EVAP hoses, canister, and gas cap. Ensure the gas cap is properly tightened or replace it if it's damaged. Next, check the EVAP purge valve and vent valve for proper function; they may need cleaning or replacement. If issues persist, use a scan tool to reset the codes and monitor the system for any reoccurrences.

To check the oil in a Dodge Neon, first ensure the vehicle is parked on a level surface and the engine is turned off. Open the hood and locate the dipstick, which is typically marked with a bright handle. Pull the dipstick out, wipe it clean with a cloth, reinsert it fully, and then remove it again to check the oil level against the markings on the dipstick. If necessary, add oil through the oil filler cap if the level is low.

Code P1689 on a Chrysler Neon indicates a problem with the Communication Bus, specifically related to the Powertrain Control Module (PCM) or the Engine Control Module (ECM). This code typically suggests that there is a fault in the communication between the PCM and other modules in the vehicle. Common causes include wiring issues, poor connections, or a malfunctioning ECM. It's advisable to check the wiring and connections first before considering component replacement.

The horn of a 1998 Plymouth Neon is located in the front of the vehicle, typically behind the front grille or near the radiator. It is mounted on the driver's side and can be accessed by removing the front bumper or grille for easier reach. If you're having trouble locating it, consulting the vehicle’s service manual can provide more specific guidance.

To replace the head gasket on a 2005 Dodge Neon, first disconnect the battery and drain the engine coolant. Remove the intake and exhaust manifolds, and then unbolt the cylinder head. Clean the surfaces thoroughly before placing the new gasket and reassembling the engine in reverse order, ensuring all bolts are torqued to the manufacturer's specifications. Finally, refill the coolant and reconnect the battery before starting the engine to check for leaks.

On a 2005 Dodge Neon, the oil pressure sensor is typically located on the engine block, near the oil filter. It is usually situated towards the back of the engine, on the driver's side. To access it, you may need to remove some components for better visibility and reach. Always consult the vehicle's service manual for specific details and guidance.

The P0551 code indicates a problem with the power steering pressure switch on your 2004 Dodge Neon SRT-4. To repair it, start by checking the wiring and connectors for damage or corrosion. If they are in good condition, test the power steering pressure switch with a multimeter to see if it’s functioning properly; replace it if it's faulty. Finally, clear the code using an OBD-II scanner and take the vehicle for a test drive to ensure the issue is resolved.

Vapor lock in a 1999 Plymouth Neon can occur due to excessive heat causing the fuel in the lines to vaporize before it reaches the engine. This can be exacerbated by factors like a failing fuel pump, clogged fuel filters, or inadequate fuel line insulation. Additionally, using fuel with a lower boiling point or a hot engine can contribute to the problem. Ensuring proper fuel system maintenance and addressing heat management can help prevent vapor lock.

Error code P2097 indicates a "Post Catalyst Fuel Trim System Too Lean Bank 1" issue in your 2005 Dodge Neon. To fix this, start by checking for any vacuum leaks in the intake system, as these can cause a lean condition. Next, inspect and possibly replace the oxygen sensor, as a malfunctioning sensor can lead to incorrect fuel trim readings. Finally, ensure that the fuel system is functioning properly, including checking the fuel filter and pump for any restrictions or failures.

The diagnostic code P1118 on a 2002 Dodge Neon indicates a problem with the intake air temperature (IAT) sensor circuit. This code typically suggests that the sensor is providing readings that are out of the expected range, which can affect engine performance and fuel efficiency. Common causes include a faulty IAT sensor, wiring issues, or poor connections within the circuit. It’s advisable to inspect the sensor and its connections to diagnose and resolve the issue.

In the 2005 Dodge Neon, the valet switch is typically located in the glove compartment or near the ignition area. It may be a small button or toggle switch, often used to disable the trunk release or limit access to certain features when valet parking. If you're having trouble finding it, consult the owner's manual for specific details related to your vehicle.

To change the timing belt on a 2003 Dodge Neon, first disconnect the battery and remove the front engine cover. Next, align the timing marks on the crankshaft and camshaft gears to ensure the engine is at top dead center (TDC). Remove the old timing belt and replace it with a new one, ensuring proper tension and alignment of the timing marks. Finally, reassemble all components and reconnect the battery before starting the engine to check for proper operation.

The P0440 and P0441 trouble codes in a 2004 Dodge Neon indicate a problem with the evaporative emission control (EVAP) system, specifically related to the EVAP system's functionality and integrity. Start by inspecting the EVAP system for any visible leaks, damaged hoses, or a faulty gas cap, as these are common culprits. If no obvious issues are found, consider testing the EVAP purge valve and the canister for proper operation. Clearing the codes after repairs and conducting a drive cycle to see if the codes return is also essential.

On a 2000 Dodge Neon, the airbag diagnostic module is typically located underneath the center of the dashboard, near the steering column. It may be mounted to the vehicle's frame or secured to a bracket. To access it, you may need to remove some trim panels or components around the dashboard area. Always ensure the vehicle's battery is disconnected before working on airbag systems for safety.

The fog light bulb for a 2005 Dodge Neon is typically a 9006 bulb. It's important to check your vehicle's manual or consult with an auto parts store to confirm this, as specifications can vary based on the trim and options of the vehicle. Always ensure you're using the correct bulb type for safety and optimal performance.

Yes, a Dodge Neon 2.0 engine can potentially mate with certain Jeep transmissions, particularly those that share a similar platform or engine family. However, compatibility may depend on factors such as the specific transmission model, bell housing design, and any necessary adapters. It's advisable to consult specific vehicle manuals or a knowledgeable mechanic for guidance on compatibility and any required modifications.

The 2000 Dodge Neon is primarily compatible with two engine options: the 2.0L SOHC (Single Overhead Cam) and the 2.0L DOHC (Dual Overhead Cam) inline-four engines. Additionally, there is a performance variant known as the 2.0L Turbocharged engine found in the Dodge Neon SRT-4, which is also compatible with the model. Overall, these engines are designed to fit within the same engine bay and share similar mounting points.

To replace a window on a Dodge Neon, first remove the interior door panel by unscrewing any screws and carefully prying it off. Next, detach the window regulator and any necessary clips or fasteners holding the glass in place. Once the old window is removed, position the new window in the track, reattach the regulator, and ensure everything is secure before reassembling the door panel. Finally, test the window to ensure it operates smoothly.

In the Dodge Neon, the crankshaft position sensor is typically located near the bottom of the engine block, close to the crankshaft pulley. It is often mounted on the transmission bell housing or the engine block itself, depending on the specific model year. To access it, you may need to remove some components for better visibility. Always consult the vehicle's service manual for precise location and removal instructions.

Diagnostic code P1390 for a Dodge Neon indicates a problem with the camshaft position sensor or its circuit. This can result in issues like poor engine performance, misfires, or difficulty starting the vehicle. It's important to inspect the sensor and its wiring for faults, and if necessary, replace the sensor to resolve the issue. Always consult a repair manual or a professional mechanic for specific diagnostics and repairs.