Flooring

You will require 101 tiles of 10"x14" to cover 95 Sft which includes a wastage of approximately 3%.

The structure is "sagging"

the floor joists have been installed the wrong way

lousy construction practice

poor design

Without seeing it the only good assumption would be that your beam or floorboards are breaking. Try pulling up some tile and checking on those and see if they are broken or deteriorating.

yes you can it makes no difference {edit:} IF you are gluing the carpet to the laminate. But if you plan to install tack strip and stretch the carpet, you risk the tension of the carpet pulling up laminate boards at the edges.

L x W / 9 = sq yards

Multiply the length times the width and divide by 9 to get the square yards. Just remember, the amount you have to buy may be more depending on the size of your room and the sizes of the rolls of carpet available.

Water and vinegar mixture for wood floors and tile, but there is. Product called Once and Done.

Assuming the plywood comes in 4' by 8' sheets you would need 6 sheets to cover a 12' by 16' area.

To remove pencil marks from a tile floor, start by using a clean, dry cloth to gently rub the marks. If the marks persist, dampen the cloth with warm water or a mild soap solution and wipe the area again. For stubborn marks, you can also try using a non-abrasive cleaner or a mixture of baking soda and water to create a paste, applying it to the marks and scrubbing gently. Always test any cleaner on a small, inconspicuous area first to avoid damaging the tile.

52 tiles (with a bit left over !)

Yes, a laminate floor will do just fine in your kitchen. Unlike wood floors, the laminate is very resistant to damage from moisture.

Be sure the sub-floor is prepared properly, however! Sever water damage to a sub-floor can cause warping and buckling if the proper materials are not used. If this happens, damage to the sub-floor will telegraph problems into your new laminate floor, causing it to warp and buckle as well.

Hire a qualified contractor to install your floor who knows what he's doing and who follows all appropriate building codes.

But a sloppy dog probably isn't much to worry about. :)

If the toilet is sitting solid on the floor, you don't need to. I would use latex instead of silicone because if you should ever have to pull the toilet, it would be much easier. One reason not to seal it down would be if the wax ring should ever fail. You could have a lot of damage to the floor before you noticed the leak.

To remove emulsion from linoleum, you can use a solution of warm water and mild dish soap to gently scrub the surface with a soft cloth or sponge. For tougher stains, a diluted vinegar solution or a specialized emulsifier can be applied, allowing it to sit for a few minutes before scrubbing. Always test any cleaning solution on a small, inconspicuous area first to ensure it does not damage the lino. After cleaning, rinse with clean water and dry thoroughly.

perhaps you would have gotten a quicker answer if you had asked-- how many bricks are needed to cover 100 square feet --or if you measured a brick wall section of 10 x 10 feet and then counted the bricks within that section. If you had done this on your own -- chances are the answer would remain in your memory for a very long time. use your investigative intuition.

Floor polish comes in many varieties, including liquid floor polish and paste floor waxes. Buy specialty floor polishes for different surfaces, including hardwood floors, concrete floors, laminate floors and vinyl-covered floors. Choosing the correct type of floor polish is important for getting the best result.

each subway tile is .13 of a sq. foot so you will need 831 pcs. to cover 108 sf.

The short answer is no.

Often steam cleaners say they can be used on "sealed" hardwood. Wood floors are put down in planks. Every board has a small space between them. Especially in winter when the humidity is lower, these spaces shrink.

A steamer is forcing water vapor into these spaces. The surface may have polyurethane, but the sides do not.

If this isn't enough to stop you, then remember wood flooring manufactures void warranties on product where water has damaged them!

First find the area of the floor and then the sheet of wood. 16*12=192 4*8=32 192/32=6 you need six sheets of plywood.

It is preferable if the toilet roll holder is placed within the toilet itself.

Usually it is within reach of the person using the toilet.

205.3125 tiles exactly OR 206 tiles, with a bit left over!

The answer depends on the units used for 10x13. It should be obvious that the number will depend on whether the tiles are 10 cm x 13 cm or 10" x 13".

A 12x12 tile is 1 sq foot, so you will need 198 tiles.

The least expensive flooring per square foot has to be vinyl 12 x 12 tiles purchased from JOB LOTstores or FAMILY DOLLAR but you get what you pay for when you are looking for CHEAP. I would still buy a can of flooring adhesive when using these cheap tiles the only problem is they may only give you a 5 - year beauty life span and then after the 5 year term you may have a heck of a glue cleaning when applying a new floor unless you either cover the old tiles with new ones or tear off the first surface wood and replace with new wood before applying new flooring. It is also much cheaper if you can do most of the sweating yourself. Use your DIY Videos and learn to save yourself some money.

828