Flooring

First find the area of the floor and then the sheet of wood. 16*12=192 4*8=32 192/32=6 you need six sheets of plywood.

It is preferable if the toilet roll holder is placed within the toilet itself.

Usually it is within reach of the person using the toilet.

205.3125 tiles exactly OR 206 tiles, with a bit left over!

The answer depends on the units used for 10x13. It should be obvious that the number will depend on whether the tiles are 10 cm x 13 cm or 10" x 13".

A 12x12 tile is 1 sq foot, so you will need 198 tiles.

The least expensive flooring per square foot has to be vinyl 12 x 12 tiles purchased from JOB LOTstores or FAMILY DOLLAR but you get what you pay for when you are looking for CHEAP. I would still buy a can of flooring adhesive when using these cheap tiles the only problem is they may only give you a 5 - year beauty life span and then after the 5 year term you may have a heck of a glue cleaning when applying a new floor unless you either cover the old tiles with new ones or tear off the first surface wood and replace with new wood before applying new flooring. It is also much cheaper if you can do most of the sweating yourself. Use your DIY Videos and learn to save yourself some money.

828

To answer this question you will need to know the size trowel you need and also the number of pounds in a bag.

A 50 lb bag using a 1/4" x 1/4" square notch trowel, you are going to expect about 80 - 90 sq ft.

The back of the bag should give you the break down for other sizes.

That would depend on the size of the tiles.

You can, but the makers don't recommend it.

Yes you can, but it's not recommended due to the different expansion rates of plywood and narrow strips of hardwood. -All the experts will tell you it should be angle-nailed.

I C F (Insulated Conctete Forms) can be purchased at the rater of $1.75 - $3.50 per sq. ft.

Assuming you mean 16x16 inches tiles... 441 tiles would cover the area exactly

350 !

6

Yes but you may want to apply a leveling compound between the two vinyls and also take care to make sure the original vinyl is well stuck otherwise they will both end up coming off the floor.

To install formica you will need a "table saw" to cut it at least a 1/2 inch over on all sides and a router to edge it off once it is laid on your surface. you can also edge it off with a good metal file but this way is done with experience-- using a metal file for formica edging is not for the novice. first remember to apply the adhesive to both the table surface and the back of the intended formica and wait about 10 minutes before mating both together and be sure to have a block of wood with a piece of carpet on it for easy pressure sliding to rub your mating pieces. Enjoy a "FREE" learning experience on your favorite DIY Video Just "Google" Gluing Formica

356 of them. Get 390 to be safe.

Humidity in room under 50%. If it's plywood sub floor moisture level should be below 12 the lower and drier you can get it the better

Magic eraser may do it. I would dampen first and not much pressure at first as it may affect floor's finish.

20 in X 20 in = 5/3 ft X 5/3 ft.

Didn't list the actual dimensions of the area to be covered, just the total, so let's split it up in the most convenient way...

400 ft2 = 20 ft X 20 ft

20 ft / (5/3 ft) = 12 tiles per side (row)

12 * 12 = 144 tiles

Insure that your concrete floor is level with no surface imperfections that change the elevations. The material used to bond the tile to the concrete substrate is commonly referred to as Thin Set. Any hardware sales place will have it and the necessary application instructions for you. Foot traffic is usually not advised for between 24 & 48 hours after the tiles are set.

Tile patterns and placement are a customer taste decision, but a tile laid in a diagonally with a perpendicular border at the wall "Scream Custom" and are a feature well worth the time and added expense of labor!

The most important thing you can do for a superior tile install is to waterproof the concrete slab before the Thin Set is applied. A Penetrating Sealer that contains no silicones, silicates or sodium silicate blends is the best you can get. Look for a 15 year warranty for waterproofing and apply 48 hours prior to tiling.

This prevents moisture from wicking up and out of a concrete to destroy the bond at your tile/substrate interface. [Hollow Sounding Tile]. After your tile set has cured use, a cemetitious based grout [not a polymer modified product] of your color choice for your grout joints. Apply the same sealer to the grout joints to waterproof them as well. This will prevent contaminates from entering the porous grout joint to discolor it and ruin the look you have worked so hard to get.

Two ways to solve this:

1. Convert both feet measurements to meters, then multiply.

2. Multiply first, then convert square feet to square meters.

A foot is exactly 0.3048 meters; therefore, a square foot, in square meters, is that same number squared.

ARTCO Floor Care Business in Sarasota charges approx. 35 cent per square foot, which includes STRIPPING & REFINISHING..(& apply FOUR COATS FINISH)...of all HARD surface floors..we also offer FREE ESTIMATES... you walk on it- we clean it !!

178 tiles