Home Appliances

The fuse is made to blow at a set amperage to protect the wire from overheating. Using anything but the fuse may cause the circuit to work but could most certainly cause the wiring to overheat and burn if it is overloaded.

actually a defective hot water has no any rating on it mainly the heater are of range of 700watt but defective heater show the same rating like the standard heatr but actually there is some looses in their internal circuits so finally defective hot water heater double ur bill.

So, u are saying that it can?

<<>>

No, a defective hot water heater can not double your electric bill.

No.

Products of combustion are:

carbon dioxide, water, carbon monoxide, and light

Carbon monoxide this is why it is vented outside.

CO is odorless and can KILL YOU.

No.

Products of combustion are:

carbon dioxide, water, carbon monoxide, and light

Carbon monoxide this is why it is vented outside.

CO is odorless and can KILL YOU.

A top loading balance is used to accurately measure the mass of an object placed on its weighing pan. It is widely used in laboratories for tasks such as weighing chemicals, samples, or other materials with precision. Top loading balances have a higher weight capacity compared to analytical balances, making them suitable for larger samples.

To stop a washing machine from moving during the spin cycle, make sure it is level on the floor by adjusting the height of the feet. Also, check that the load inside the machine is distributed evenly. Using anti-vibration pads or adding weight on top of the machine can also help stabilize it during spinning.

Use the formula I = W/E, Amps = Watts/Volts. Apply the voltage of the generator to the formula and the results will be the amount of amperage the generator will produce.

Yes, you can use Bounce dryer sheets in energy efficient Kenmore dryers. Dryer sheets can help reduce static cling, soften clothes, and add a pleasant scent to your laundry. Just follow the dryer manufacturer's guidelines for proper use.

The electric switch heater uses high voltage, from 480 to 750 volts, through coils that are fixed both on the web of the rails and with "crib heaters" that are laid underneath the movable rods between the ties.

These are typically more effective than other types of switch heaters because of the ability to provide the crib heaters, which cannot be used with gas heaters.

The heating elements are provided throughout the area of the movable parts of the switch layout.

The 120 volt equipment is likely to burn up or burn out sooner. The filaments in a 120 volt bulb will burn a lot brighter for a much shorter period of time. That is how movie studios used to produce a lot of light without using expensive equipment. They would replace light bulbs every day. Electric motors would be far more powerful and run hotter. Movie studios used them for special effects. They did not care if an elevator took off like a rocket once and burned out the motor.

The metal prongs of a plug are sealed in plastic or rubber to provide insulation and protection against electric shock. This covering helps prevent accidental contact with the metal prongs, which carry electricity, making the plug safer to handle and use.

You can measure the height of a refrigerator by using a measuring tape or ruler. Place the measuring tool vertically from the floor to the top of the refrigerator to get an accurate measurement in inches or centimeters.

No, there are two reasons, usually the 240v plug is different and will not fit into a standard 120v outlet. Second, it needs another 120v leg, that is, the 240v uses two

120v wires for the power it needs. So if you did get it to plug in and it did run, it would

not be running at the power it needed to run, so there is a chance of damage to the appliance.

What should be done is have an electrician install the correct outlet for it, this way you don't take a chance on damaging the unit and also the unit is safe to run.

What if you change the plug or get it to work, you might not be using the ground or

the neutral might be switched with the ground, in this case, you could create a unsafe condition and put family at risk.

<<>>

The pin configuration of the 240 volt receptacle is different from a 120 volt pin configuration. This is a safety factor to prevent the wrong voltage being applied to the wrong devices.

It is not recommended to reverse the wiring of a dryer heating element as it can cause damage to the appliance and create a safety hazard. If you are experiencing issues with your dryer heating element, it is best to consult a professional appliance repair technician for proper diagnosis and repair.

There is technically no such thing as a propane gas stove. You would buy a gas stove, and then convert it to using propane with a propane conversion kit generally consisting of new burner orifaces

Charlie's Appliance in Marshall is a good, reputable, factory-trained dealer. Give him a call.

A Kenmore 80 series washing machine has a capacity of around 3.2 to 3.5 cubic feet, which typically translates to about 8-12 pounds of laundry per load, depending on the fabric type and how tightly packed the laundry is.

yes they can my microwave has been starting to turn it self on and cooks with nothing inside till I stop it , it keeps reseeting itself to start cooking again till you stop it , this is a obvious risk do to fire and microwave needs to be unplugged right away and thrown out and buy a new one , HUGE FIRE RISK !!!!

You can use a 2-prong to 3-prong adapter that connects to the 2-prong outlet and provides a 3-prong outlet for the washing machine. However, it's important to ensure the electrical wiring in your home is safe and compatible with the adapter to prevent any electrical hazards. Alternatively, consider hiring a licensed electrician to upgrade the outlet to a 3-prong outlet for safer use.

No matter what brand it is, it has to be where the gas valve goes into the manifold.

Where the burner tube is, there is either the igniter or hot surface igniter.

Just take your model # of the dryer, and either go to the MFG website,or go to a parts

store online and put in you model # and you will be able to look at the diagram of your dryer, this way you know exactly where it is.

Here is a great place for parts,and also you can look at your diagram.

http://www.partselect.com/MultiModels.aspx?ModelNum=KGHS02RMT&searchTerm=&RefineSearch=0

There are two different gas orifice's. Some are color coded, and some can be reversed.

LP --NG, There can be a lot of info, so, usually if the stove can be converted, it comes with a kit, and instructions. Contact the MFG if you don't remember the kit coming with the appliance. You must check if this can be done,and follow the MFG. I do not want anyone to get hurt so I will not explain it in depth. There is usually a air mixture adjustment

that must be made, and should not be done by someone that has not done it before.

You could cause to much carbon monoxide from the wrong adjustment. It only takes a pro

less then 45mins.

Unless people put down the exact model and serial #'s , you get a general description.

Best to take the screws out, shove the pipe further into the fitting and re screw it. If you are going to use tape use the metal foil tape where you peel off the paper on the back exposing the glue side.

Carbon monoxide is produced when air holes become blocked in a water heater. This gas is colorless, odorless, and highly toxic when inhaled in high concentrations. It is crucial to maintain proper ventilation to prevent carbon monoxide buildup.

No, it is not safe to plug a 220 volt heat pad bought in China into a US 120 volt outlet. The voltage difference can damage the heat pad and pose a safety risk. You would need a transformer or voltage converter to safely use the heat pad in the US.

One common reason for a gas dryer getting hot then turning cold is a blocked vent or exhaust system. This can cause the dryer to overheat and then shut off to prevent a fire. Another possibility is a malfunctioning cycling thermostat or gas valve that needs to be replaced. It is recommended to have a professional technician inspect and repair the dryer to ensure safe operation.