0
Industrial Engineering
Industrial Engineering is the branch of engineering that deals with the creation and management of systems that integrate people and materials and energy in productive ways. An industrial engineer studies industrial productivity and makes and implements recommended changes.
2,298 Questions
How does a ring fetter shaft coupling work?
The ring fetter is made up of 3 pieces. The outer cylinder, inner cylinder and the locking bolts. As you draw in on the locking bolts (usually caps screws) the inner and outer cylinders are squashed together locking the shaft to the bearing. To remove there are jacking bolt holes. The ring fetter is a one shot deal. the cylinders are distorted and win not seat properly again.
Bob Page
Maintenance Mechanic
Covidien
How do you calculate horse power of water pump?
You can approximate the horsepower capabilities of any electric motor by calculating incoming electric power. This is done by simply multiplying the rated voltage by the rated current. This will give you a unit of watts. There are about 746 watts per horsepower. Say if the motor is about 85% efficient, then incoming power will match output power minus this efficiency. Anyways, multiply incoming power by .85 and divide by 746 should give an approximate horsepower of the water pump's motor.
What equipment is used to check phase rotation?
A phase rotation meter. Or a small three phase motor can be wired up and its rotation observed.
Is standard ansi b16.5 applicable for valve over 24 inch?
B16.5 Is limited in all respects to 1/2" - 24". So the answer is no. for a complete listing of the dimensions provided in B16.5 see www.texasflange.com
Define the term zero error of vernier calliper?
How can you tell the difference between a general and specific tolerance on a drawing?
IDK that is why i asked
General tolerance refers to all untoleranced dimensions, and should be covered by a note on the drawing, eg tolerance unless noted otherwise plus or minus 0.25 mm
Specific tolerance will be included with the individual dimension, either as dimension limits or dimension plus tolerance.
Why is concrete reinforcement wire mesh called BRC?
Concrete reinforcement mesh is not called BRC. BRC is the name of a company that supplies reinforcement and it may be that the buyer has specified that it is supplied by BRC.
Pass design for channel section in rolling mill?
All depends on the channel size, 7 or 9 passes required to reduce from a rectangular or square starting section. The bar is almost completely enclosed by the top roll in a "closed pass" sequence of grooves and the thickness of the web and flanges is progressively reduced. A control or edging pass before the finishing pass regulates the final flange length, area reduction in the last pass is minimal to avoid excessive pass wear.
There are dfferent types of cooling towers available in Industry.
Some of the commonly is used cooling towers are
- Round Cooling Towers
- Square Cooling Towers
- Dry Cooling Tower
- Wooden Cooling Tower
- Cross Flow Cooling Tower
- Modular Cooling Towers
- Evaporative Cooling Towers
- Natural Cooling Towers
- Counter Flow Cooling Towers
Get a highly durable cooling tower according to your industry.
What is the difference between Class TPS and Type X Current Transformers?
I am aware that Class TPS current transformers have a Low Leakage Flux design
What is the main advantage of stainless steel over mild steel?
Many stainless steels are stronger. It's also more corrosion resistant.
What is the definition for Geometric Constraint?
More a technique than an application, geometric constraint solving consists of finding configurations of points, lines, circles, and other geometric figures constrained to have certain relations to each other. This sort of problem finds applications in a number of areas including computer aided design, molecular modeling, and robot motion planning.
What was the first car to use interchangeable parts?
The first car to use fully interchangeable parts was the Cadillac Model K. On March 5 1908 three Model K's were driven hundreds of miles, disassembled, had all parts jumbled together, were reassembled from parts selected at random, and were driven further hundreds of miles. This feat won the Dewar Trophy for Cadillac. Early Ford Model T cars by contrast still required hand work to fit parts to individual vehicles.
What is the tip of the thread called for a sixty degree thread form?
The 3 main parts of a Screw thread are :-
Root ....... (bottom)
Flank ....... (sides)
Crest ........(top)
Is carbon steel the same as mild steel?
both of these are same In some places they are used interchangeabl
low carbon steel has 0.05-0.15% carbon
mild carbon steel has0.16-0.29% carbon
http://www.metalsupplies.com/
It's seems as though you have answered the question yourself. You have stated exactly what it is (manufacture and model number). It was made in China and their exclusive distributor here in the US is "Instrument Sales & Service" out of Wilmington, DE. In case you need it, their number is 1-800-874-7637.
You will need a footing to support a moment of 21,000 ft.lbs.
Moment = Arm x Force
Moment = 1000 lbs. x 14 ft. = 21,000 ft.lbs.
Slip rings are used in AC while split rings are used in DC generators
